Installation of a washing machine by level. Proper adjustment of the legs of the washing machine

I teach household appliances repair masters! Salary from 80,000 !

The correct installation of the washing machine is no less important than its proper operation. Its further work will depend on how responsibly you approached the installation procedure. Therefore, the first thing you should worry after the purchase is how to install a washing machine exactly. For the machine to serve for a long time and regularly, does not jump on the floor during washing, it is not enough just to twist the legs on the washer. The installation process should be prepared in advance and start with a place determined for the constant deployment of technology. How to put SMA, how to align it in order to avoid unpleasant situations during operation, read below.

Alignment instructions

Choosing a place for installation, having unscrewed from the washing machine, you can start installing it. First, the equipment is connected to communications, because all hoses are connected from the back and it will be inconvenient to climb them if the equipment is moved to the wall. After the machine is connected and put in its place, you can begin to align it.

Before installation, check the evenness of the floor itself, it should not have a strong difference, protrusions and holes, if this is found, then it will be very difficult to set the washing machine in level. It is necessary to align the floor first.

In order to set the position of the washing machine by level, you just need to adjust the height of the legs. There are such legs in all washing machines. In some models, only two legs are regulated, and in others. all four. We perform the following:

  • With the help of the key that comes with the washing machine, you need to loosen the locknuts on the legs.
  • Screw all the legs to the end, if there is a need for the machine to stand higher, then unscrew them to the desired height and visually achieve an even position.

If the machine is flooded in some direction, then you need to twist, you need a leg from the side where the car is leaning.

The adjustment of the legs continues until the washing machine rises steadily, and in terms you will see a strictly horizontal position.

At the end of the work, be sure to fix the locknuts on the legs so that they do not stray from the desired level. Sometimes, in order to achieve a stable position, you do not need to twist the leg, but slightly move the machine to the right or left, forward or backward. In general, in order to establish perfectly correctly the machine, you need to stock up on patience, it does not always work out to do it quickly. That is why experts recommend installing a washing machine on a tiled floor or floor with a cement screed.

However, even a correctly installed washing machine can be lost over time. From what it comes? Everything is simple, firstly, the machine can move from constant vibrations, and secondly, the soil on which the house is built can “move”, which means that the level of construction is also shifted.

Why do it?

A logical question arises, why then align the machine in terms of level? Despite the various factors, you need to do this. After all, an incorrectly installed machine will vibrate excessively, and sometimes jump. Excessive vibration of the drum and the entire washing machine leads to a faster wear of parts, the technique breaks.

Most often, the following troubles come from vibration:

  • a plastic tank cracks;
  • Cracking tiles in the room on the wall on the tins of a vibrating machine;
  • The machine “leaves” from its place;
  • bearings wear out.

To install the machine correctly, and it did not jump, some users, based on their experience, recommend using rubber glasses under the legs. They are attached on the floor and reduce the vibration of the machine.

So, you can set the washing machine by level yourself. If you have no desire to do such work or not for this tool, then call the master so that it does not jump later, but just do not leave the machine in an unstable position!

Washing machine, especially automatic. absolutely necessary thing in the household. You just need to load the linen and add the detergent. and then the smart device will do everything on its own.

For the car to work for a long time and reliably, it is required to provide it with all the necessary conditions. Therefore, the moment of installation is very important. Correct connection will provide high quality washing and trouble.free operation.

Think about where and how to put the car, you need to buy. Its dimensions, power, type of design are determined not only by the wishes of the hosts, but also by the presence of opportunities in the apartment.

How to adjust the legs of a washing machine. How to align the washing machine by level

There are several factors because of which the washing machine can jump or vibrate during the washing process: not remote transport fasteners, a drum overload, counterweight, bearings, or a malfunction of other internal mechanisms. However, the most common cause is poor.quality installation. For quiet and safe washing, you should correctly put the washer on a flat horizontal surface using a construction levelmaker or other available methods.

A flat installation of a washing machine is important

Depending on the brand of the smell, it has 2 or 4 adjustable legs. To install the washing machine, it is necessary to choose a place that fully meets the installation requirements. You can not place the unit close to the walls or to furniture. The surface on which the SMA will be placed should be even, without hollows and protrusions. Well, if the base is lined with tiles. The hard base will put up the unit in terms of level without additional shock.absorbing glasses, which will simplify the process.

The concrete base should be even and not crumble. If pieces are chopped down when tapping the material, then it is better to cover it with tiles or install another hard stand. The poorly adjusted machine will vibrate and move, which can lead to the operation of the protection or the rapid wear of the bearing and its failure.

With a high speed of rotation, the drum can touch the surface of the tank and, if the last plastic, damage the walls.

Properly exhibited unit will ensure safe and correct operation throughout the entire period of operation.

The choice of a suitable place for a washing machine

An important step when installing the unit is the choice of a suitable place. The placement method depends on the presence of free space, the location of communications, as well as the type of unit. Classic option. installation in the bathroom. There is access to cold water, sewage and power networks. When the space is limited, you can install a washing machine under the sink. When choosing a location for the unit with vertical loading, make sure that there is enough space for opening the lid.

Classic version for installing a washing machine-a bathroom. There are necessary communications and the ability to connect to the mains

The built.in technique is gaining more and more popularity. Such a washing machine can be built into a column or placed in the kitchen under the countertop. This is an ideal option for small.sized apartments with limited free space.

Unusual location of the unit. the hallway. But if there is enough space and you can bring communications, then this option is quite convenient and ergonomic. Here you can install a drying machine.

An important criterion when choosing a place is the presence of a solid and stable surface. The ideal option is naked concrete or floor tiles. When installing on a wooden floor, be prepared for strong vibration of the unit during washing and spinning.

How to put it correctly

To smoothly install a washing machine, you need:

  • Delete all transport bolts and check the ease of rotation of the drum.
  • Loosen the locknuts on the legs using the key coming in the kit.
  • Complete the supports.
  • Adjusting the legs to achieve a stable position of the unit.
  • Set the building level on the top cover of the lubricants parallel to the control panel. If the air bubble moved to the right, then you need to adjust the legs on the left side, and vice versa. The machine is installed correctly when the ball is placed between two average risks.
  • Locate perpendicular to the previous position. Align the machine with twisting the front or rear legs.

HE Washing Machines: Everything You Need to Know!

Set the smell until the device shows the horizontal position in both directions. Sometimes when moving the machine on the floor, you can find a position in which adjustment is not required. This is possible if the base is made as even as possible. After we finished installing the unit, it is necessary to fix the nuts in the upper position using the key, otherwise the adjustment will be violated when vibration occurs. This can lead to independent movement and breakdown of the washing machine.

How to adjust the legs of a washing machine

Vibrations are a serious problem that can cause irreparable harm: they lead to violations of screws, bolts and other fasteners in the typewriter. Vibrations also cause frequent breakdowns of a plastic tank. if it bursts, water flows. So that all these problems do not happen, you need to twist the legs on the washing machine.

Incorrect installation threatens not only breakdown of washing machine, but also damage to surrounding objects. The machine can move with strong vibrations.

Special adjustments provided by the manufacturers of the smell are provided with a flat and correct installation.

To increase or decrease the height, screw the leg into the body or twist it from it. These actions will help to level the machine without much effort.

The installation sequence

The new car delivered from the store first needs to be released from packaging and transport fasteners. Then it is connected to all the required communications and regulated by the height of the legs. After that, the unit is ready for the first wash.

Removing transportation fasteners

When transporting, moving parts are fixed to avoid damage. If you do not remove these fasteners (bolts, staples, bars), then when turned on, the mechanism will inevitably fail. Necessary:

All these details need to be saved. They may be needed if you have to move or take the car for repair.

Decorative plugs are inserted into the place of bolts, which are included with the machine.

Water supply

Cold water supply occurs through a flexible hose, which is included in the supply kit. It is not recommended to make a completely strict connection, since vibration will be transmitted to the pipes system through it and gradually destroy them.

The hose is connected to the water supply through a specially cut pipe or tee. It is usually equipped with a mesh filter for water purification from gross pollution. From the side of the machine, the connection is carried out through a standard threaded connection.

Draining

The easiest way to organize water drainage is to lower the end of the drain hose into the bath or sink. But this is rather a temporary solution.

Most often, the spent water is drained through a special branch directly into the siphon under the sink. The length of the hose should be sufficient to form a loop sagging down. There is constantly water in its fold, which prevents the scentes of the sewer to get into the car.

Legs adjustment

The drum of the car should rotate smoothly and without distortions. For this, it is necessary that its upper plane is located strictly horizontally. This can be checked using the construction level. If the deviation exceeds 2 °, the machine’s adjustment is used. In all modern models, they have a threaded setting.

Power supply

The best solution is to connect the machine to the shield using a separate three.wire cable, on which a protective machine is installed. To protect against closing on the case, an RCD device is used.

The socket must necessarily have grounding and mounted at a certain height from the floor level so that water does not get into it when leak. In the kitchen, these requirements meet an electric stove socket.

How to get out of the situation

What makes the washing machine jump? As a rule, this is the relief of the flooring on which it is installed. Therefore, you will definitely have to take care of ensuring that the device is as smooth as possible. If you cannot achieve this, then the constant “dances” of the cars on the exalting will lead to a gradual promotion of the legs of the machine. Therefore, first of all, you need to take care of the quality of the stand.

Wood will help you achieve your goal. In particular, you can use:

Put the washing machine so that it stands even, and the problem will be solved on its own, at least until the stands are worn out, you can forget about the existence of this problem.

By laying tiles, it is necessary to observe its level not only for it to have an aesthetic look. If it is broken, the installed machine, as we already said above, will begin to jump. In the absence of materials for the substrate, the way out will be slightly different. If three legs are installed at the same level, it is advisable to put them on the bottom of the liquid nails from below. For full stability, the same procedure is done with the upper part of the support, but if you do not want to spoil the thread, you can limit yourself to a counter.hawk.

If the basis for your washing machine is, for example, a parquet, you must think about the installation site in advance. In that place, the floor should be reinforced and leveled. To do this, you can use the bars of the substrate.

How to adjust the washing machine yourself

Of the tools we need the most ordinary building level. At the first stage, you need to select the installation site. It is desirable that there is a concrete floor with good stability here. In some cases, a separate concrete screed is created under the machine so that it stands on a solid base.

As soon as the site is ready for the machine, we install it. we just put it on the selected base and connect it to the water supply, sewage and power grid. Make sure that the body of the apparatus does not squeeze the hoses going to communications. Adjusting the height of the legs, bring the car to such a state that it does not swing. we achieve a visually correct position. Accordingly, the leg is twisted in which direction the body is flooded when it is sweding.

Пральна машина Bosch.0- error 0. Null. Zero. Not working. How to fix?

We recommend: how fast and high.quality masonry occurs?

Rotating clockwise, the legs are screwed and become shorter. If you start twisting the legs in the opposite direction, then they will become longer. What do we need to do with these legs in the end?

How to put it correctly

To smoothly install a washing machine, you need:

  • Delete all transport bolts and check the ease of rotation of the drum.
  • Loosen the locknuts on the legs using the key coming in the kit.
  • Complete the supports.
  • Adjusting the legs to achieve a stable position of the unit.
  • Set the building level on the top cover of the lubricants parallel to the control panel. If the air bubble moved to the right, then you need to adjust the legs on the left side, and vice versa. The machine is installed correctly when the ball is placed between two average risks.
  • Locate perpendicular to the previous position. Align the machine with twisting the front or rear legs.

Set the smell until the device shows the horizontal position in both directions. Sometimes when moving the machine on the floor, you can find a position in which adjustment is not required. This is possible if the base is made as even as possible. After we finished installing the unit, it is necessary to fix the nuts in the upper position using the key, otherwise the adjustment will be violated when vibration occurs. This can lead to independent movement and breakdown of the washing machine.

Why is the correct adjustment of the legs important

Adjusting the legs of the washing machine allows it to give it stability. The drum of the machine, spinning even at low speed, creates serious vibrations that arise as a result of uneven distribution of underwear. For linen itself, they are absolutely harmless, but the knots of the washing machine begin to wear out faster.

Vibrations are a serious threat to any household appliances. Under its influences, screws, screws and other types of fastening are spanning, plastic weakening occurs. Due to vibrations, there are often malfunctions associated with damage to the plastic tank, as a result of which it can burst-water spilled out of it will flood the neighbors from below. And all this could have been avoided if the legs of the washing machine were adjusted in height.

Incorrectly adjusted car breaks not only itself. Subject to vibrations, it can budge and damage the surrounding objects. Most user claims are due to the fact that their cars literally “jump” around the bathroom. And few can figure out that you just need to adjust the legs and give the machine a strictly horizontal position. In addition to vibrations, a trembling machine will make a noise that interferes with others.

We recommend: how to cut tiles without tile cutter: inventions and homemade

See what we get as a result of improper adjustment: a washing machine jumping around the bathroom; Tanned from vibrations; Tiles falling from random blows against the wall; Broken bearings inside the washing machine.

If you want to extend the life of your washing machine, install it correctly.

adjust, washing, machine, terms

Step.by.step instructions for installation

The installation of the washing machine should begin with the preparation of the place where it will be installed. For models with horizontal loading of space, more, while with vertical. less.

The first error when creating an installation site is the installation of a device in a niche, which practically squeezes the machine on the sides. Such a solution can lead to the problem of vibration almost immediately, since the devices still create them and for this you need a space-about 3-4 cm on each side, otherwise you can observe the problem of beating the device about the walls of the furniture.

Many masters say that the minimum gap with furniture and equipment should be 1 cm, but this is not enough for most models.

Installation scheme: 1. machine, 2. connection to the mains, 3. water supply pipe, 4. sewer adapter

When choosing a place, you should pay attention to:

The basic installation circuit consists of such steps:

  • removal of all transport devices;
  • Connecting to the sewage system and the water supply system. the main difficulty here is the selection of adapters for pipes, they should be selected according to the diameter of the typewriter and pipes pipe;
  • Connecting the adapter to the water supply system. it is better to install it at the junction of the crane with the water supply;
  • installation of the sewage adapter;
  • connection to sewage and water supply systems;
  • legs adjustment by level using a construction level with jewelry accuracy.

The largest difficulty in installing is the type of flooring, on which the “activity” of the machine depends. When installing on a tile (on a tile) or on a wooden floor, there should be no problems with installation, since such surfaces are even and solid, which is necessary.

Important! Laminate and linoleum are softer coatings, so it is recommended to lay an additional solid layer in the form of a wood-based stove on them.

Recommendations to reduce vibration

There are some tips to reduce vibration:

  • No need to overload the machine with things. modes with the most acceptable weight are always described in detail in the instructions for the device;
  • It is worth using anti.vibration stands and rugs;
  • It is worth checking the level of fixation of the machine and adjust it;
  • Replacing bearings and shock absorbers, if it comes to old technology.

These tips will help reduce the noise level that occurs when spinning, but no more.

Anti.vibration stands and rugs

Rugs and stands to reduce vibration are effective assistants to reduce the level of oscillations.

Vibration rug

Mags of two layers were made. the upper rubber to align the level of the legs and the lower foamed layer to prevent the transfer of vibration to the floor. Claims are more often rubber or consisting of a rug with a special pallet for extinguishing vibrations.

Legs adjustment by level

The drum of the car, rotating even at low speed, creates vibration. With an uneven distribution of linen, it becomes stronger. Vibration is dangerous because the details of the machine wear out from it faster. How to install a washing machine so that it does not jump? The answer is simple. set the legs in level.

Attention. The adjustment of the legs in height will reduce vibration and give the apparatus stability.

To begin with, adjusting the height of the legs, the machine is brought into a stable state (so that it does not swing). After that, take the building level and set it parallel to the front wall. The front legs are adjusted so that the air bubble is exactly in the middle.

Then the level is alternately rearranged to the side walls of the machine and the rear legs are regulated. The final result of the work should be a position when the machine body is stable, and the level shows a strictly horizontal position both in front and from the sides.

Installation without a level

If you do not have a construction level, then instead you can use a glass or saucer with water. Dishes with water are placed on the top cover of the washing machine and adjust the legs so that the water in a glass or saucer is at the same distance from the edge of the dishes.

Why is the washing machine jumping?

The first cause of strong vibrations may be non.replaced transporting bolts. They motionlessly fix the tank inside the case so as not to damage it during transportation. Before starting work, the bolts and other fixing elements must be removed. Operating a car with them is strictly prohibited. The next reason for vibration is the uneven distribution of things in the tank. If you start the device with an empty tank, it will not vibrate. The same thing will happen if you distribute things perfectly evenly. with an even layer throughout the circumference of the tank. In reality, it is impossible to achieve such a distribution, even evenly distributed at the beginning, in the process of washing are mixed.

Tank suspension malfunction and supporting bearings. Weakening of the consignment of the counterweight.

The purpose of the system from springs, dampers and counterweight to make the frequency of the tank of the tank is much lower than the frequency of its rotation. This reduces the amplitude of the oscillations and the magnitude of the vibrations transmitted to the body. In order to better understand the previous paragraph, remember: at the beginning of the spin, the case of the loaded machine is swaying stronger, and then with an increase in the speed of rotation of the tank, the swing passes into a small trembling or, with proper distribution of linen, practically disappears.

Pump the tank. after that he must make no more than one hesitation and stop. Otherwise, shock absorbers are faulty, they must be replaced.

Open the casing, inspect the elastic elements. metal should not have deformations, rubber. tears and cracking. Defective details. for replacement! Check the counterweight mount. if it hangs out, tighten the nuts.

Figantous bearings. When working, there should not be any creaks and knocks. Twist the tank manually, shake from side to side. Having discovered a creak or beating, replace faulty parts.

Proper adjustment of SMA

The choice of installation location

To properly set the automatic machine, start by choosing a place to install. The surface should be as flat and solid as possible. The tile will be the best option.

Do not place the washing room on the wooden floor. Over time, under the weight of the device, wooden boards will begin to bend, and each subsequent washing will be accompanied by the jumps of the unit and increased noise.

The surface should also not be slippery. If necessary, you can use special anti.slip rugs or anti.vibration stands. The technique should be stable, without any distortions.

Level adjustment

To set the equipment in level, to know how to adjust the legs of the washing machine and how to fix them correctly. How to proceed further? Read step by step instructions below.

  • Praise the machine carefully forward and backward. This will help to determine which leg you need to twist.
  • Loosen the puck on the leg and twist it. To increase the height, you need to twist counterclockwise (that is, twist) to reduce (screw). clockwise. If you need to adjust two or more legs, do it alternately.
  • Check the technique for stability again. If the machine is staggering, the twisting procedure must be repeated. The main thing is to achieve complete stability of the device.
  • Fix the adjusting legs. The mechanism of their fixation in different models may differ. Therefore, it is better to read the instruction manual.

If the legs are not recorded after adjustment, then during operation they certainly. As a result, the adjusted height will be beaten, and the washer will begin to “ride” the floor.

To make sure of the absence of a washing machine to the side, be sure to use the construction level. How to eye the washer with its help?

  • Take the tool and place it on the top cover of the device case so that it is placed first parallel to the front and rear wall, then. parallel to the side.
  • Look at the position of the air bubble. It should be strictly in the center.
  • If necessary, repeat the procedure of twisting the adjusting legs and re.tighten the washers.

With such simple manipulations, you can adjust the most accurately and evenly installing machine machine. The main thing is not to neglect the rules and not exhibit the device “by eye”. Then the machine will work properly, relatively silently and as long as possible.

How to adjust the legs of a washing machine

Vibrations are a serious problem that can cause irreparable harm: they lead to violations of screws, bolts and other fasteners in the typewriter. Vibrations also cause frequent breakdowns of a plastic tank. if it bursts, water flows. So that all these problems do not happen, you need to twist the legs on the washing machine.

Incorrect installation threatens not only breakdown of washing machine, but also damage to surrounding objects. The machine can move with strong vibrations.

Special adjustments provided by the manufacturers of the smell are provided with a flat and correct installation.

To increase or decrease the height, screw the leg into the body or twist it from it. These actions will help to level the machine without much effort.

No need to twist the legs at once at once.

Important points when adjusting the legs

I understand how to adjust the washing machine, you can twist or unscrew the legs, installing it in an even position. To check the inclination of the smell, you will need adjusting the washing machine by level. With it, you can measure deviations.

  • Install the tool on the upper part of the washing body.
  • Attach the level so that it is located parallel to the walls of the machine. Bubbles in flasks should be within its lines. The same applies to the installation of the tool in parallel to the side walls.
  • Deviation in any direction. evidence that it is required to adjust the legs of the washing machine. How to do this. we have already sorted out.

About how to correctly adjust the legs, there is a lot of video on the network. To cope with this task, use one of them:

Why is the correct adjustment of the legs important

Adjusting the legs of the washing machine allows you to give the device stability. The drum of the machine, spinning even at low speed, creates serious vibrations that arise as a result of uneven distribution of underwear. For linen itself, they are absolutely harmless, but the knots of the washing machine begin to wear out faster.Vibrations are a serious threat to any household appliances. Under its influences, screws, screws and other types of fastening are spanning, plastic weakening occurs. Due to vibrations, there are often malfunctions associated with damage to the plastic tank, as a result of which it can burst-water spilled out of it will flood the neighbors from below. And all this could have been avoided if the legs of the washing machine were adjusted in height.

adjust, washing, machine, terms

Incorrectly adjusted car breaks not only itself. Subject to vibrations, it can budge and damage the surrounding objects. Most user claims are due to the fact that their cars literally “jump” around the bathroom. And few can figure out that you just need to adjust the legs and give the machine a strictly horizontal position. In addition to vibrations, a trembling machine will make a noise that interferes with others.

See what we get as a result of improper adjustment:

If you want to extend the life of your washing machine, install it correctly, and we will help you with pleasure.

adjust, washing, machine, terms

How to adjust the washing machine yourself

The store employees told you that the machine should install the machine? Tear this with your hand. acting according to our instructions, you can install and adjust it yourself. The most important thing we need to do is to correctly adjust the legs of the washing machine. Of the tools we need the most ordinary building level. At the first stage, you need to select the installation site. It is desirable that there is a concrete floor with good stability here. In some cases, a separate concrete screed is created under the machine so that it stands on a solid base (this applies to houses and apartments with wooden floors).

When installing the machine, you need to think in advance the conditions and the mode of its operation. In accordance with this, you can take measures in advance that will help to avoid problems in the future.

In a private house

During the construction or repair of a private house, you can even create the necessary scheme for wiring pipes and electric cables at the design stage. In the presence of a dry basement in the house, washing and drying equipment is often installed there. In this case, the residents do not interfere with noise, smells and dampness.

In the kitchen and in the corridor

The washing machine fits quite easily into the interior of the kitchen, although the washing process itself does not go very well with the cooking and eating.

In the corridor it should be installed only in the most extreme case.

At the same time, many issues will have to be resolved:

  • where to find a place so that the car does not interfere with walking and open the doors;
  • how to hide the laid communications (on the floor, walls);
  • how to hide the equipment from the eyes of guests (built.in cabinet, curtain).

On a wooden floor or laminate

Perfect hard and hard floor for installation. concrete. On wooden floors, the vibration of the machine intensifies and destructively affects the unit itself and surrounding objects. Various options for strengthening the floor are possible: