Repair of the oven of an electric stove Hephaestus with your own hands

The Gefest 6140-03 electric stove is a classic representative of this type of kitchen technique. It has a white color of the body and the black door of the oven; Thanks to this combination, the plate is perfect for any kitchen interior.

The hob consists of 4 cast-iron fireparents of various power:

The hob itself is covered with white enamel, which, although reliably protects against damage and corrosion, but rather praised and very difficult to clean.

The capacity of the oven is as much as 52 liters, which is very good and enough for the largest family. But not only the volume is impressive, but also the functionality, which consists of 7 operating modes, and the main among them are as follows:

The rest is a combination of these 3 options, as well as spinning with barbecue.

The slab is controlled by a mechanical way, and the choice of the necessary parameters is rotated by rotary switches. To maintain the necessary temperature in the oven, a thermostat is provided, and the timer will be worried so that your products do not get drunk.

The main advantages of Gefest 6140-03 I believe:

The disadvantage of the stove is that its case heats up very much during operation, but otherwise, is a good unit for that kind of money.

Gefest 6140-020001

Gefest 6140-020001 is an electric stove that has standard dimensions: height-85 cm, depth and width-60 cm. The device consists of a hob and oven. A noteworthy feature of this device is its brown color, so not everyone will approach the interior of the kitchen.

There are 4 burners of various capacities on the hob:

The role of heating elements are ordinary “pancakes”. They are warming quite quickly, but their temperature is slowly adjusted. The panel is covered with enamel is the cheapest material, which, nevertheless, copes with its task, but is very bad to clean. The oven of the Gefest 6140-020001 relatively large sizes-52 liters, which is quite enough even for a large family.

  • lower heat/upper heat;
  • lower heat/upper heat and convection;
  • grill;
  • grill and spin (it goes in the kit);
  • convection and annular heating element;
  • convection, annular heating element and lower heat.

With such a set of operating modes, you can cook any dishes, there is only a small nuance: the power of the oven’s hets are not very large, so the food will prepare longer than usual.

There is an electromechanical timer, so you can set a certain preparation time after which the signal will sound.

At the bottom of the plate there is a spacious drawer for dishes.

So, I will classify Gefest 6140-020001:

I will classify the disadvantages with only the small power of the oven.

Necessary tools

Before you put the door of the oven, whether it is an electric or gas model, you need to prepare the following tools:

The latter will need when you need to install a new glass. When cleaning, put rubber gloves. While working with glass. dense mittens. The design of many models of modern ovens allows you to remove the door without tools, but they are necessary to repair other parts.

How the loops are removed

The door may work incorrectly due to loops. If these details are faulty, it will not completely close or hard to open.

The loops must be removed, and then install them in place or put new. To do this, remove the door and unscrew additional mounts. On some models of oven cabinets, springs are on both sides.

In order not to break the loops at all, they must be removed carefully, to be extremely attentive. You can’t crush much. otherwise they will bend or break. Manufacturers of kitchen technology of Darina, Zanussi, Kaiser, Curting, Samsung, Electrolux, hotpointer Ariston and others try to make ovens so that the process of removing and disassembling and adjusting the doors is uncomplicated. If during work it is felt too strong resistance of devices, then disassembly is done incorrectly.

Certain rules must be followed and then the loops will not break. Before they are to be removed, you should make sure that all the screws are twisted. Even the remaining detail will lead to the fact that the mounts will bend, they will need to be changed. When you have to remove the door or glass, you cannot use force. Ovens have a design in which all mechanisms and elements as a whole are removed without difficulty.

You need to remove the loops carefully so as not to damage them

Independent repair

You can repair only burner and oven door yourself. With more serious breakdowns, it will be necessary to attract a third.party master with appropriate access to work with such equipment.

For self.repair, you will need:

  • cross.shaped and straight screwdrivers;
  • Passatigi;
  • a divorce key of 15-20 millimeters;
  • gas lubricant;
  • FUM tape for gas equipment.

Depending on the cause of the malfunction, a cleaning agent and soft brush may be required.

What to do if the electric lights are out of order

Problems with electrical engineering mainly arise due to a short circuit that occurred due to the fault of flowing water. To eliminate this malfunction, it will be necessary to clean and dry the wires laid from the generator block (located at the end of the stove, under the hob) to the burners). Further, these parts must be placed on plastic stands. Also, electric fires are out of order due to fat carcass accumulated on the candles. To eliminate this malfunction, you need:

  • disconnect the wire from the candle installed on the burner;
  • remove the fixing plate and remove the candle;
  • Rinse the candle in a strong solution of detergent, dry and return to place.

These two reasons for the failure of electric lighting can be eliminated independently.

How to repair the oven door

It is necessary to repair the oven door when this element does not fit the device to the body. Such problems arise for two reasons:

If the cause of the loose fit of the door is caused by loose mounts, then the latter must be tightened. And the leap gasket should be replaced with a new.

door, gefest, stove, household, rules

How to adjust the gas supply

This procedure must be carried out if the flame disappears or it is intermittently burning. In this case, you will need to block the crane on which the gas is supplied and remove the partition. Next, you need to find out which damper failed. After that, the installation screw blocking the plate should be promoted.

At the end of the procedure, you need to re.check how the gas is supplied, and if necessary, repeated adjustment.

How to replace nozzles

Over time, nozzles on gas stoves are clogged, which is why the flame burns unevenly. To eliminate this problem, you will need to disassemble the burner and clean it with a wooden toothpick from traces of carbon and other particles. If the burner has stopped working, the part should be removed and replaced with a new. To do this, you need to promote the screws fixing the element to the hob.

We stell up the tool for repair

For the repair of gas boards at home, a minimum number of tools will be required, first of all:

  • A universal screwdriver with interchangeable nozzles. a cross and a standard straight slot, pliers;
  • A small divorce key with the departure of the side lips of 15-20 mm;
  • FUM tape for gas devices;
  • Solid gas grease;
  • Soft brush and highly effective detergent.

You can take “CIF”, “Cleaner” or any other liquid gel used for cleaning gas plates with a stainless base from burned fat. Sometimes, in extremely rare cases, to repair the plate, you have to use a multimeter.

And, of course, good health will be required, at least there should not be a runny nose, otherwise it will be difficult to catch a gas leak, and in working with gas devices the main condition for success is the safety of work. For the most serious work with the coupling compounds in the gas stove, a watercolor brush and diluted liquid soap are required.

DIY GAPETENT DIY DIY

Details: Repair of the Hephaestus gas stove doors with your own hands from a real master for Olenord.com.

Without the manipulations indicated in this article, it is impossible to replace the hinge (loops) of the oven doors, t.to. Without removing the inner glass of the oven, it is physically impossible to get to the hinge, because it is located inside the door frame, inside, between the glasses. Therefore, if the inner glass has not yet been removed, you are here.

Damage to the door hinges, after which the oven blooming usually follows and the complete impossibility of frying the appetizing, crunching gose crust is frequent.

First, let’s start with the design of the hinge itself and with the little secrets that you need to know.

In a hurry, you can dart to the door and try to remove it immediately. Do not try. only scrap will help. It’s all about. The hinge consists of two halves.

One half is tightly screwed to the frame of your gas stove.

over, when replacing the hinge, it remains untouched. The other half, equipped with a spring, starts with its “hook” and, after docking, is fixed with a lock. You can’t notice this lock right away. No need to break the door. Just raise the flags on both hinges. after which the door of the oven is elementary removed. In the photo, the red arrow indicates the latch. One thing, of course, when the hinge lies calmly on the table. Another. when we look at the stove. Therefore, we give a photo where the connector’s lock is shown right on the door of the oven, so to speak, in working condition.

After removing the door, it remains only to unscrew two screws. In the photo they are marked. Hinges (loops) of the oven doors are presented as a complete set ready to install. This set consists of two hinges. over, they are interchangeable. That is, there is no idea to place them on the door: this should be on the left and the other on the right. It is impossible to make a mistake when replacing a hinge. The response part is not supplied in the kit, as unnecessary. Because nothing happens to her.

If you have a small breakdown of the gas stove, for example, the burners stopped burning, you do not immediately rush to contact the workshop or emergency gas service. Most likely, there was such a breakdown as clogging of contacts. Correction of the breakdown will take only 5 minutes of your time, while it will work to save money and time that will need to be spent on calling the master. Therefore, you must understand that the plate can be repaired on your own.

You can’t imagine any kitchen without a stove, because it occurs the process of cooking a variety of food. Mostly everyone knows why gas stoves are more in demand than electric. The very first advantage of the stove operating from gas lies in the fact that food is prepared much faster.

How to fix the problem with gas or electric stove with your own hands?

Below are the instructions regarding the removal of the door, dismantling the loops and restoring the previous state of the stove. Recommendations will come in handy with serious problems with the door, glass or hinges.

Necessary tools

For each specific case, you will need different tools, but the general list will look like this:

  • Cross and ordinary screwdrivers;
  • Passatigi;
  • a hammer;
  • glue-mixer for installing new glass;
  • dense mittens or rubber gloves (depending on the type of breakdown).

Many plates are designed so that the door can be removed without tools, but tools are necessary to repair other parts.

Attention if you need to replace some element (loop or glass), you need to purchase it.

Removing the door and glass

Open the door. Find loops on the sides. Depending on the design of the plate, they need to be bent or lifted and moved to yourself. Smoothly pull horizontally on yourself, and then vertically up. it should disconnect from the body. Put the removed door on a flat and soft surface so as not to damage the glass

On some models of plates, the side parapets must first be removed. It is necessary to open the clamping lever on the hinges, and then cover the door so that it fixes the hinges. Then it is removed, the sidewalls are removed and accessed to the brackets with which the door is pressed to the stove.

The door can be disassembled to free the glass, but this will be discussed later.

In the clamping mechanism of the oven, you need to carefully examine all the loops, brackets (they are easily unscrewed or removed from the case, but on some plates you will have to remove the side walls of the oven)

If some curvature is visually noticeable, then you can try to carefully straighten the part with a hammer and plots. If your actions have not brought results or the part is broken without the possibility of recovery, install a new bracket for your slab model

Put the door with the outer side down on an even soft surface. Inspect it: Most often, metal profiles and screws are used to fix the glass

The screws need to be unscrewed. The released glass is carefully lifted and pulled out. You can start replacing it or cleaning it.

The advice after the repair all actions are performed in the reverse order: the glass is placed inside, pressed with screws, the door itself is carefully hung on the plate case.

We suggest watching a video on how to remove the oven door:

Dismantling of loops

Often in improper work the door is to blame the loop. Due to their malfunction, the door opens too tight or does not close completely. The reasons:

Regardless of the causes of the loop, you need to remove, and then clean or changed to new. To do this, after removing the door, you just need to unscrew the additional mounts.

On some ovens, the springs are installed on both sides.

In order not to finally damage the loops, they need to be dismantled carefully and carefully. With excessively high strength, the parts can bend or break

Manufacturers make ovens such that the doors can be removed without difficulty. If too strong resistance of the mechanisms is felt, dismantling is performed incorrectly.

Cleaning the door from dirt

On many modern plates, the function of self.cleaning of the oven is built, in which the walls and glass are cleaned by the steam. This method can be applied on simpler models. To do this, boil water in a pan, and then put it in the oven, included on a small fire, and leave it for half an hour. The steam will facilitate the subsequent cleaning and get to the most inaccessible places.

It is important not forget to clean the rubber seal.

For cleaning, you can use special store products, but improvised substances are suitable. Several effective recipes:

  • Take 2 glasses of warm water, add a little liquid soap there and 0.5 hours. l. soda. A well.placed liquid must be placed in a sprayer and spray the product on metal and glass. After half an hour, rinse with warm water pollution.
  • Prepare a thick mixture of water and soda, apply it with a thick layer to contaminated places. After a few hours, rinse the mixture and retired dirt.
  • Mix soda and citric acid, apply powder to a wet polluted area. After a couple of hours, the dirt is easy to remove with a soap sponge.
  • Alcohol solutions are effectively cope with fat and soot.
  • To combat pollution, vinegar can be used. Dilute 2 tbsp. l. vinegar 1 l of water.

Powders lead to the formation of microcracks in the glass, so it is better to use solutions for its cleaning.

Design and main components of the electric stove

The electric stove looks very impressive. it is a complex household device, but its design is quite simple, and all the main working elements are in a special heat.resistant case, which is made of stainless steel.

The principle of operation is similar to all electrical household appliances: current, passing through heating elements (heating element), heats them to a given temperature. The plate has several capes on the hob, and their number varies: at least two, and the standard. 4 pcs.

The structure of the firewood is quite diverse. Classic is the burners on the enameled hob from the heating element inside, modern are continuous surfaces of ceramics with various types of heater built into them. Consider the main types of fireplace.

  • Old domestic options are equipped with cast iron products, they slowly heat up and cool, creating a steam effect in the kitchen, but they are resistant to moisture and high temperature.
  • Tubular spirals. they are made of a hollow tube, when heated, such devices not only give heat, but also contribute to the circulation of warm air inside their body, which significantly increases the efficiency of their operation. These products are very difficult to repair independently.
  • Ceramic burners are very simple in design, it is easy to repair them at home. a spiral made of nichrome is laid in special cells in a circle and fixed. In modern models, glass.ceramic continuous plates are increasingly used. they are more durable and it is easy to wash them.
  • Halogen devices are special burners with a similar emitter, which are installed in different places of the hob. A stove with such burners provides rapid heating, in a second, and small electricity consumption, so they are the most economical, but only professional masters can be engaged in repair.

All models of modern boards for transmitting current to burners use a special section power wire, in addition, they are connected to regulators and thermostats that provide their protection against overheating.

Repair of the oven of the gas stove Hephaestus with your own hands

Details: Repair of the oven of a gas stove Hephaestus with your own hands from a real master for Olenord.com.

Without the manipulations indicated in this article, it is impossible to replace the hinge (loops) of the oven doors, t.to. Without removing the inner glass of the oven, it is physically impossible to get to the hinge, because it is located inside the door frame, inside, between the glasses. Therefore, if the inner glass has not yet been removed, you are here.

Damage to the door hinges, after which the oven blooming usually follows and the complete impossibility of frying the appetizing, crunching gose crust is frequent.

First, let’s start with the design of the hinge itself and with the little secrets that you need to know.

In a hurry, you can dart to the door and try to remove it immediately. Do not try. only scrap will help. It’s all about. The hinge consists of two halves.

One half is tightly screwed to the frame of your gas stove.

over, when replacing the hinge, it remains untouched. The other half, equipped with a spring, starts with its “hook” and, after docking, is fixed with a lock. You can’t notice this lock right away. No need to break the door. Just raise the flags on both hinges. after which the door of the oven is elementary removed. In the photo, the red arrow indicates the latch. One thing, of course, when the hinge lies calmly on the table. Another. when we look at the stove. Therefore, we give a photo where the connector’s lock is shown right on the door of the oven, so to speak, in working condition.

After removing the door, it remains only to unscrew two screws. In the photo they are marked. Hinges (loops) of the oven doors are presented as a complete set ready to install. This set consists of two hinges. over, they are interchangeable. That is, there is no idea to place them on the door: this should be on the left and the other on the right. It is impossible to make a mistake when replacing a hinge. The response part is not supplied in the kit, as unnecessary. Because nothing happens to her.

Sooner or later, the need to make the repair of a gas stove overtles almost all the owners of these devices.

It’s often invoice to contact the master, and I would like to eliminate home problems so as not to waste time transporting tiles and repair.

There are a number of problems of gas plates, for example, adjusting the electric carpet, which you really can cope yourself with yourself.

The analysis of the most common breakdowns in the slabs and ways to solve them will help you with this, as well as a video that reflects all the stages of work.

Before engaged in repair, you need to understand what gas tiles are, what parts are present in it, and what kind of repair of a gas stove with your own hands may be required in one case or another.

Many firms producing gas stoves: Gorenje, Ardo, Ariston and T.D. But all tiles, even if they differ in price, have a similar type of internal device.

A gas stove device: with your own hands, how to disassemble the Hephaest, how to disable it during the repair

Gas stove device: 7 operation requirements

You can figure out the principle of operation of the gas stove if you study its device a modern improved gas stove has a rather complex device, however, if you understand the design features, you can easily repair the device with your own hands. However, if you need to replace the gas stove, then it is imperative to contact the state gas service, since the slightest malfunctions and violations can provoke very serious problems.

Everyone knows that combustible gas mixed with air is explosive, which is why, for the sake of safety, they add a special substance with a pungent smell in small quantities. In the case of gas leakage, it is necessary to call the GAZ control service.

In order to completely protect yourself and your house from the explosion of gas during repair work, you must comply with certain requirements, namely:

  • Fully de.energize the apartment, turn off the main machine or twist traffic jams;
  • Make mobile devices with autonomous power and de.energize;
  • Open the doors and windows in the entire room;
  • Use only special tools and components;
  • Block the shut.off valve;
  • Eliminate existing malfunctions;
  • After work, supplied gas, opening the valve.

Before starting the repair of a gas stove, you should completely de.energize the room

If after the repair work and gas supply, an incomprehensible hiss or smell of gas has appeared, you need to block the valve again and contact a gas service specialist. You can independently fix a gas stove and eliminate the available malfunctions quite easily and quickly, the most important thing is to clearly follow the instructions and follow the safety rules. If you need to repair a gas stove yourself, then initially you need to decide how exactly the device works and which nodes and details allow it to work normally.

The modern gas stove consists of such systems as:

The base part consists of fireproof, burners, shut.off valves and pipelines. The electric part is responsible for good lighting, electric fire, and sometimes, in some models, also for the grill system, if it is installed in the oven. The supporting structure is mainly the case of the product made of stainless steel.

Each gas stove has a standard set of parts. Depending on the model of the device, it can have a different configuration and certain nuances, however, their equipment is unchanged.

One of the main parts of the gas stove is the burner located inside the stove under the most hob itself, and firewalls are located on top of the burner, which during wet cleaning can be removed and washed, however, the most important thing is that water does not get into the cutters. Each burner is characterized by a specific certain power and is determined by such indicators as: the minimum flame when the handle is in the extreme left location; medium fire. flame regulator stands in the middle; maximum burning when the regulator is located in the right position. When choosing a product, you need to pay attention to such an indicator as maximum combustion power. It is determined by the level of gas combustion and is indicated in the technical characteristics of the gas stove itself.

All gas stoves, without exception, use three types of burners, namely:

Diffusion burners are characterized by the fact that the gas stream enters the burner, where it is mixed with air. When the oven burner is lit, the air is taken from the inside of the plate. The principle of operation of a kinetic burner implies that the gas is mixed with air when moving and then the combustible mixture switches to the burner. In modern models, a mixed version is used, that is, part of the air is taken from the inside of the device, and the rest comes from the outside.

Repair of a gas stove requires certain skills and it is very important to know how to correctly disassemble the device in order to carry out the required work. Before analyzing the product, you need to block the valve of the gas crane. If you perform all actions according to the instructions, then the parsing of the stove and the elimination of problems can be done yourself. Then you need to turn off the stove from the gas network and electricity.

The plate should be disassembled in several stages

Dismantling the slab consists of several stages, namely:

  • Remove the burners, turn the bolts, raise the top cover;
  • For access to the Shiber of the oven, it is necessary to remove the side wall;
  • Remove the nozzle of the burners.

If there are problems with the operation of the slab and the burners are poorly lit, then the mandatory adjustment of the ignition is required. If only the burner burns weakly, then the problem may be clogging. Repair is carried out very simply, since it is enough to clean the nozzle using a thin wire or needle for this. It is not always easy to get to the nozzle’s nozzle, for this you need to unscrew the lower wall of the oven, remove the burner and clean the nozzle.

DIY overshadows repair with your own hands

Details: Repair of brass cabinets Hephaestus with your own hands from a real master for Olenord website.com.

Without the manipulations indicated in this article, it is impossible to replace the hinge (loops) of the oven doors, t.to. Without removing the inner glass of the oven, it is physically impossible to get to the hinge, because it is located inside the door frame, inside, between the glasses. Therefore, if the inner glass has not yet been removed, you are here.

Damage to the door hinges, after which the oven blooming usually follows and the complete impossibility of frying the appetizing, crunching gose crust is frequent.

First, let’s start with the design of the hinge itself and with the little secrets that you need to know.

In a hurry, you can dart to the door and try to remove it immediately. Do not try. only scrap will help. It’s all about. The hinge consists of two halves.

One half is tightly screwed to the frame of your gas stove.

over, when replacing the hinge, it remains untouched. The other half, equipped with a spring, starts with its “hook” and, after docking, is fixed with a lock. You can’t notice this lock right away. No need to break the door. Just raise the flags on both hinges. after which the door of the oven is elementary removed. In the photo, the red arrow indicates the latch. One thing, of course, when the hinge lies calmly on the table. Another. when we look at the stove. Therefore, we give a photo where the connector’s lock is shown right on the door of the oven, so to speak, in working condition.

After removing the door, it remains only to unscrew two screws. In the photo they are marked. Hinges (loops) of the oven doors are presented as a complete set ready to install. This set consists of two hinges. over, they are interchangeable. That is, there is no idea to place them on the door: this should be on the left and the other on the right. It is impossible to make a mistake when replacing a hinge. The response part is not supplied in the kit, as unnecessary. Because nothing happens to her.

Modern ovens break quite rarely, but problems in their work are not excluded. The difficulty is that the design and all its elements do not provide for extraneous intervention. Repair of ovens at home is usually carried out by replacing components and conducts it in most cases an experienced master. However, in some cases, breakdowns can be eliminated independently.

If you decide to try to repair the oven with your own hands, then you should know situations when this should not be done. Definitely do not need to open the body if:

  • The electric oven is under warranty;
  • The oven’s information panel shows that the problem is to break down the complex component;
  • You don’t know anything in electrical engineering.

During the warranty period, all repairs are made for free. With the exception of the following cases:

  • There are traces of opening attempts on the design. erased or damaged heads of bolts, screws, removed seals.
  • Insects or rodents penetrated the oven, which caused a short circuit or mechanical damage to the nodes and wires.
  • The connection was made incorrectly, without compliance with the recommendations of the manufacturer.
  • Damage to the electronic components occurred due to changes in voltage parameters, as a result of which it went beyond the critical limits indicated by the manufacturer.

A gas stove device: with your own hands, how to disassemble the Hephaest, how to disable it during the repair

Gas stove device: 7 operation requirements

You can figure out the principle of operation of the gas stove if you study its device a modern improved gas stove has a rather complex device, however, if you understand the design features, you can easily repair the device with your own hands. However, if you need to replace the gas stove, then it is imperative to contact the state gas service, since the slightest malfunctions and violations can provoke very serious problems.

Everyone knows that combustible gas mixed with air is explosive, which is why, for the sake of safety, they add a special substance with a pungent smell in small quantities. In the case of gas leakage, it is necessary to call the GAZ control service.

door, gefest, stove, household, rules

In order to completely protect yourself and your house from the explosion of gas during repair work, you must comply with certain requirements, namely:

  • Fully de.energize the apartment, turn off the main machine or twist traffic jams;
  • Make mobile devices with autonomous power and de.energize;
  • Open the doors and windows in the entire room;
  • Use only special tools and components;
  • Block the shut.off valve;
  • Eliminate existing malfunctions;
  • After work, supplied gas, opening the valve.

Before starting the repair of a gas stove, you should completely de.energize the room

If after the repair work and gas supply, an incomprehensible hiss or smell of gas has appeared, you need to block the valve again and contact a gas service specialist. You can independently fix a gas stove and eliminate the available malfunctions quite easily and quickly, the most important thing is to clearly follow the instructions and follow the safety rules. If you need to repair a gas stove yourself, then initially you need to decide how exactly the device works and which nodes and details allow it to work normally.

The modern gas stove consists of such systems as:

The base part consists of fireproof, burners, shut.off valves and pipelines. The electric part is responsible for good lighting, electric fire, and sometimes, in some models, also for the grill system, if it is installed in the oven. The supporting structure is mainly the case of the product made of stainless steel.

Each gas stove has a standard set of parts. Depending on the model of the device, it can have a different configuration and certain nuances, however, their equipment is unchanged.

One of the main parts of the gas stove is the burner located inside the stove under the most hob itself, and firewalls are located on top of the burner, which during wet cleaning can be removed and washed, however, the most important thing is that water does not get into the cutters. Each burner is characterized by a specific certain power and is determined by such indicators as: the minimum flame when the handle is in the extreme left location; medium fire. flame regulator stands in the middle; maximum burning when the regulator is located in the right position. When choosing a product, you need to pay attention to such an indicator as maximum combustion power. It is determined by the level of gas combustion and is indicated in the technical characteristics of the gas stove itself.

All gas stoves, without exception, use three types of burners, namely:

Diffusion burners are characterized by the fact that the gas stream enters the burner, where it is mixed with air. When the oven burner is lit, the air is taken from the inside of the plate. The principle of operation of a kinetic burner implies that the gas is mixed with air when moving and then the combustible mixture switches to the burner. In modern models, a mixed version is used, that is, part of the air is taken from the inside of the device, and the rest comes from the outside.

Repair of a gas stove requires certain skills and it is very important to know how to correctly disassemble the device in order to carry out the required work. Before analyzing the product, you need to block the valve of the gas crane. If you perform all actions according to the instructions, then the parsing of the stove and the elimination of problems can be done yourself. Then you need to turn off the stove from the gas network and electricity.

This magic disc stove is too easy to use, and mother in law exaggerate! Heroes H3 High end time f

The plate should be disassembled in several stages

Dismantling the slab consists of several stages, namely:

  • Remove the burners, turn the bolts, raise the top cover;
  • For access to the Shiber of the oven, it is necessary to remove the side wall;
  • Remove the nozzle of the burners.

If there are problems with the operation of the slab and the burners are poorly lit, then the mandatory adjustment of the ignition is required. If only the burner burns weakly, then the problem may be clogging. Repair is carried out very simply, since it is enough to clean the nozzle using a thin wire or needle for this. Getting to the nozzle of the oven is not always simple, for this you need to unscrew the lower wall of the oven, remove the burner and clean the nozzle.

DOORS on budget. [Doors 1 to 100 | Full Walkthrough]. Roblox Doors Fanmade

Necessary permits

To change the equipment connected to the gas network, you need to act in the manner prescribed by law:

  • Write a statement addressed to the head of the REU Gorgaz with the corresponding request. A sample application can be taken in the district department.
  • The gas service employees will determine the complexity and specifics of the work, and then write out the account, which must be paid.
  • Upon completion of the installation of equipment, specialists will make a record in those. passport.

Before writing the application, you have to provide: an apartment passport and documents for a new gas stove. At the end of the installation, you will be issued an agreement for the provision of services.

Service cost

There is no clear rating of the gas stove installation. Payment is charged from you only after the new stove is installed in the apartment.

Keep in mind that if you use the services of a store or a certified commercial organization, the employees of which will install a plate taking into account all the norms, you will still have to call Gorgaz employees. In this case, you will have to pay for an additional.