Please read the following instructions before serving the refrigerator.

  • Check the insulation resistance of the device.
  • Disconnect the device from the network before service maintenance to prevent electric shock.
  • Whenever testing is carried out when the power is on, put on rubber gloves to avoid electric shock.
  • When using any device, check its correspondence for measuring the current, voltage and power.
  • Do not touch metal products in the freezer with wet hands. This can cause frostbite.
  • Make sure that water does not fall on electrical elements from the mechanical parts.
  • Когда проводится проверка нижнего раздела холодильника с открытой верхней дверью, двигайтесь с осторожностью, чтобы не удариться о верхнюю дверь.
  • When you need to tilt the device, take out any materials from the shelves and the shelves themselves, especially the glass.
  • When servicing the evaporator, put on cotton gloves. This is necessary to prevent injuries from sharp edges.
  • Repair the refrigeration circuit in a specialized service center. Gas inside the circuit can pollute the environment.

Refrigerant charging in the compressor.

Test the refrigerator by connecting it to the electric network before refueling. It is necessary to establish the performance of the motor-compressor and immediately identify defects of the entire system. If the defects were detected, the possible residues of the refrigerant R134A are removed by breaking the end of the tube in a narrow place. (Rice. one)

Replace the filter and all damaged components. Fall out and remove a piece of the remaining tube and then seal the tube with the Hansen clutch for the same place. (Rice. 2)

LG French Door Refrigerator. In Door Ice Maker Troubleshoot (2018 Update)

Soldering operation must be performed with an open valve so that the flux vapors can freely go out. The solder should be without shells between two tubes, it must be borne in mind that in the process of heating the ration point expands. The tube is equipped with a dad Hanzen with a coupling and connected to a vacuum pump tube. (Rice. 3)

The air begins to pump out from the system after starting the pump. The cooling system should be under the vacuum, before the manometer of the vacuum is indicated (0 Absolute.1 atm760 mm Hg.Art.) In any case, it is desirable that the pump operates for approximately 30 minutes. (Rice. 3)

If a leak is detected, it is necessary to stop the vacuum pump and add a small amount of freon to the system if the vacuum cannot be obtained (the pressure gauge cannot fall to.1 atmosphere), start a refrigerator and find a leak using a current. With a defective soldering, when the valve is opened, normal external pressure inside the contour is not restored. This is because the remnants of the solder are absorbed into the tube and block it, the pressure should be leveled when the valve is opened.

As soon as vacuuming is finished, add the required number of grams of R134A to the refrigerator. Remember that each system should be seasoned with an exact amount of R134A with a tolerance of ± 5 grams. (Rice. four)

Before performing this operation (if the vacuum pump and the gas station are connected), make sure that the valve is closed in front of the vacuum pump to save the freon when adding to the system. (Rice. 5)

In addition, check, a graduated scale on the cylinder for the amount of R134A, which will be added, for example, if we have 750 grams of freon in the cylinder and we need to add 165 grams to the circuit, this result will be achieved when the R-134A decreased to 585 grams, Controlling this by the indicator. Do this after choosing the appropriate scale for gas pressure, gas pressure is indicated by the manometer on the upper part of the column.

In order for the R134A to enter the system, open the valve at the base of the cylinder connected to the gas station. Freon cannot be added to the system all at once, because this can lead to blocking the motor-compressor. After adding about 20-30 g, it is necessary to immediately close the feed.

The pressure rises and the compressor engine sucks the gas and the pressure decreases again. The adjusting valve is opened again until the required amount of R134A reaches the refueling. When the system operates, the input pressure should be stabilized from 0.30 to 0.6 atmosphere.

Model GC-389

Name specification
Dimensions (mm) 595 (W) x626 (D) x1880 (h)
Weight without packaging, kg 74
Cooling system No frost
Control test. Refrigerated Selector
Frost Button
Defrosting system Automatic
The heater of the latch
Door edging Met. moldings or plastic with metallized coating
The case outside Enamelized steel sheet
The case is inside Hygienic plastic
Filling out the case Polyurethane foam
Defrosting device Closed Ten
Reflash R134A (135g)
Compressor grease Freol @ 22G (210 cc)
Departments of the refrigerator Transparent shelves (3 pcs)
Vegetable container (2 pcs)
Vegetable container with a lid (1 pc)
Cooling container (1pc)
Door departments Milk with a lid (1 pc)
Egg (2 pcs)
Small (5 pcs)
for bottles (1 pc)
Departments of the freezer Tray (4 pcs)
Ice tray (1 pc)
Compressor Launch from the thermostat
Evaporator Tubular type
Capacitor Tubular type

Model GC-349

Name specification
Dimensions (mm) 595 (W) x626 (D) x1710 (h)
Weight without packaging, kg 69
Cooling system No frost
Control test. Refrigerated Selector
Frost Button
Defrosting system Automatic
The heater of the latch
Door edging Met. moldings or plastic with metallized coating
The case outside Enamelized steel sheet
The case is inside Hygienic plastic
Filling out the case Polyurethane foam
Defrosting device Closed Ten
Reflash R134A (135g)
Compressor grease Freol @ 22G (210 cc)
Departments of the refrigerator Transparent shelves (2 pcs)
Vegetable container (2 pcs)
Vegetable container with a lid (1 pc)
Cooling container (1pc)
Door departments Milk with a lid (1 pc)
Egg (1 pc)
Small (3 pcs)
for bottles (1 pc)
Departments of the freezer Tray (4 pcs)
Ice tray (1 pc)
Compressor Launch from the thermostat
Evaporator Tubular type
Capacitor Tubular type

Questions and answers

If the problem with the box is saved, you can leave an application to the service service to call a specialist.

Extraction and installation of drawers in the freezer department.

Product storage, advice cooking, note

If ice cubes are needed as early as possible,

Cold air circulation allows

or other products requiring strict

Product storage recommendations

Cleaning, general information, carefully

Power supply: a break in power within 1

the legs of the refrigerator, wrap them against

During loading and unloading, refrigerator

Before turning on: if transportation of the refrigerator

Cryadagent circulating inside the system

cooling, can grunt quietly, even

worry, it’s completely normal. AT

The process of working the refrigerator can be

Caution, NOTE NEWS

Anti.condensate tube: anti.condensate tube laid

In these places, the refrigerator can strongly

warm up, especially immediately after the first

to the left, depending on the layout of your

Install the lower door loop.

Before calling the repair service, read this section.

Before you call the repair service, read this section or call the service

customer support. This will help save time and money. This list includes in

yourself the most common cases that are not the result of bad

assembly quality or low.quality materials used in this device.

Check the presence of voltage. Ensure the contact of the fork with

outlet. Cm. p. 5 “When connecting to the source

It is necessary to check if the fork is tightly inserted into the outlet.

Contact the seller or authorized service center.

The refrigerator is located too close to the source

The refrigerator doors often open or

left not closed for a long time.

The doors of the branches are not closed tightly.

Cm. section “Search and elimination of malfunctions” (the door is not

The refrigerator stands on the floor in an unstable position.

Adjust its position using adjustable

The refrigerator applies to surrounding objects.

The doors were not closed densely or the products interfere

Doors open too often and for a long time.

Hook inside a container with products. normal

Products interfere with door closing.

Move the products that interfere with the door closing.

Tighten adjustable legs. The place where it is installed

refrigerator, can be uneven. With help

adjustable legs lift the front part

Gently with a rag to remove garbage from rubber

Incorrect door reassignment.

The function of fast freezing is not turned off is not disconnected.

Cm. Section “Operation” (fast freezing).

The refrigerator is located close to the heat source.

The refrigerator doors often open or leave

not closed for a long time.

The doors of the branches are not closed tightly.

Cm. section “Search and elimination of faults” (door

Warranty conditions, disposal of the old refrigerator, note

Warranty conditions see. In a warranty coupon.The guarantee does not apply: the consumer complaints that arose in

In case of deviation from state

detailed information on maintenance and use of the refrigerator you

You can find on the official website of LG in the section “Frequently set

LG No Frost refrigerator cleaning equipment

You can use both chemicals and remedies made by yourself to wash the refrigerator.

  • Pour hot water into a bowl, add a couple of teaspoons of washing gel to it, mix the components until the foam is formed;
  • Moisten a soft sponge in the solution, wipe all the elements pre.extracted from the device (shelves, gratings, boxes) and the internal and external surfaces of the refrigerator;
  • After removing pollution, be sure to rinse off the remnants of the cleaning agent with water.

Suitable for washing the refrigerator and other chemicals in the form of various sprays, fluids, foam, wet napkins (TOP House, Silel Bang, Hors).

In addition to remarkable cleaning properties that allow hostesses to get rid of pollution in the device in a short time, most of these funds have disinfectants.

IMPORTANT! When working with special drugs, do not forget to put rubber gloves on your hands. After cleaning the surfaces, be sure to wipe them with a rag moisturized in clean water.

Folk methods will help you rid the refrigerator from spots of various origin:

  • Make a soda solution of 2 tablespoons of powder and 1 liter of water, treat them with the internal walls of the chambers, rinse the surface with water;
  • Grate half the bar of laundry soap, mix chips with warm water. Remote pollution from problem areas;
  • Moisten the sponge in hydrogen peroxide (3 %) and wash the chambers.

The sealing tape on the doors of the device can also be cleaned with a detergent for dishes, hydrogen peroxide.

The use of vinegar, soda for the removal of mold or fat from the rubber element is unacceptable, since these substances can lead to corruption of the part and violation of the tightness of the chambers.

If you notice that the tape has lost elasticity. apply a little olive oil on a rag and rub it into the seal.

IMPORTANT! To wash the refrigerator, chemical aggressive drugs (containing chlorine, concentrated acids, alkalis) and abrasive agents cannot be used. Process the surfaces of the electrical appliance only with soft rags or sponge.

Getting rid of unpleasant odors in the refrigerator LG No Frost

The appearance of unpleasant odors in the device is most often associated with improper storage of products (non.compliance with the rules of commodity, storage of damaged food and t.D.).

To get rid of the “aroma”, first of all, find out and eliminate the reason for its occurrence.

The following methods will help to eliminate the pungent smell from the refrigerator:

  • Mix vinegar with water in equal proportions and wash the internal walls of the camera;
  • Pull 20-30 tablets of activated coal, pour it on plates or in bags of gauze fabric, put the product inside the refrigerator;
  • The crushed crusts of citruses (lemon, orange), black tea, sugar, rice, vanilla, coffee grain (pre.chop them) are well “absorbed” (pre.chop them): as in previous cases, place the products in bags made of linen, gauze, put it inside the household devices.

Effectively eliminate even the most caustic smell of special balls for refrigerators, which are sold in household chemical stores.

The mineral components contained in them destroy the unpleasant “amber” and prevent the appearance of mold. The balls are valid for 3-4 months, after this period, the drugs should be replaced with new.

ADVICE! Do not forget to take care of the device if you need to leave for a long time: defrost, wash the device and leave it disconnected, with an open door.

Carry out a periodic check of products in the unit, throw out food, the expiration date of which has expired, store food in special containers closed with a lid.

The purity in the refrigerator is not only the key to your health, but also a long service life of kitchen appliances.

Boxes below meat?

Other users noted that these boxes are designed to store meat, as this is the cool place in the refrigerator. And the ice crust that is formed on it helps the product to remain cooled and last longer.

One of the users noted that the meat should always be at the bottom of the refrigerator, since if it flows, then the drops will fall on other products. The use of products spoiled by meat juice is fraught with food poisoning.

It is worth noting that many users and subscribers of this group agreed that these boxes for storing meat.

Storing meat in boxes is a great idea, because it is easy to get and wash it if the meat flows.

There were users who use the boxes at the bottom of the refrigerator and not for meat, and not for vegetables. One person wrote that he noticed the inconvenience of storage of vegetables in these boxes, but found that beer cools faster there.

This is also a good idea: below in the refrigerator you can store your drinks.

Of course, not everyone can manifest such a problem, because each of us has different models of the refrigerator. Maybe your model is suitable for storing vegetables.

There were users who said that it was in the instructions for the refrigerator that it was said to store vegetables and fruits in these boxes.

The opinion of the chef

But in the chat under the photograph there was a user who did not agree with all participants. This is the chef Mimi Morley.

The woman said that the boxes at the bottom of the refrigerator are unequal. These boxes can really be used to store vegetables and fruits. However, you need to determine in which box is low and high humidity. Vegetables such as cabbage, carrots or, for example, strawberries, must be stored with a moisture content of 30-40 percent.

Low humidity box should be filled with goods that release gas. They are not so sensitive to moisture loss. These include bone fruits and apples, also kiwi.

The competent distribution of vegetables across the refrigerator will help to avoid unnecessary food waste, and will also help save the products as juicy and fresh as possible.

I repeat, I closed the question on the low side and I hope for a long time, I did not harm. Why is it perplexed because of this? There is or existed such a concept “do worse, so that it is still called. “So, from the very beginning of his labor path, he tried not to adhere to this.

Review of common breakdowns

To eliminate the malfunctions that occur in refrigerated units, it is necessary to have minimal ideas about the most common breakdowns. Since independent repair is simply impossible without an adequate response to the problem that has arisen, study in detail the reasons why certain situations arise.

The refrigerator flows

Can be caused by mechanical damage to the case, destruction of the thermal insulation layer and, as a result, violation of the temperature regime. In this case, condensation is formed at the place of damage, which flows down the refrigerator. To eliminate the malfunction, it is necessary to restore the thermal insulation layer and patch the hole.

The refrigerator is rewinds and there is an irrigation

If when the door is opened, you witness the intended layer of hoarfrost and freezing products, then this situation could arise if:

  • The cooling level is set too strong, adjustment is required; with a temperature sensor, compressor installation, etc.D.;
  • The door seal does not fit loosely, which could happen due to the loss of elasticity;
  • Flapsed and it is required to replace the thermostat; does not close to the end due to the overflow of the cooling chamber.

A special metal probe is used to check the density of doors at the factory, which at home can be replaced by a strip of paper. At the place of penetration of paper under the magnetic strip, there is an air of air from outside, which determines the deposition of ice and more hard cooling.

The refrigerator turns on, but does not freeze and does not cold

  • Malfunctions of the thermostat or setting the cooling mode for a minimum;
  • Malfunctions of complex electronic control units in modern models;
  • Random launch of defrosting, while you need to completely defrost the refrigerator and turn it on again;
  • Sharp loading of two.chamber refrigerators with large volumes of products that it does not have time to cool;
  • A refrigerant leak, while you need to urgently find the damage site and eliminate it;
  • Compressor motor malfunctions or clogging of the entire cooling system.

The refrigerator does not turn on

With such a problem, check the electric circuit for its integrity. At the same time, such reasons for the breakdown are possible:

  • Household appliances are not included in the outlet, insufficient level of voltage in the network or the outlet is faulty;
  • It is necessary to check the plug and cord chain for integrity; relay or electric motor.

Modern Atlant, Samsung and others may not turn on due to failures in the control unit. Detecting such problems at home is quite difficult.

Long work without disconnecting

In normal mode, you will hear active work within 10. 20 minutes. Then it should turn off until the next cycle. Otherwise, rapid wear of rotating elements occurs. The reason for the problem may be:

  • Quite a closed door or hot air of the surrounding space, because of which the desired level of temperature is not achieved in these household appliances; It operates in super.sulfuria, but such work cannot last longer than the regulated by the factory instruction;
  • The thermal electronic sensor failed;
  • Freon leaks from the cooling system.

Increased noise

For the correct operation of the unit, its installation is carried out using the construction level and on a solid base. If these requirements were not fulfilled and the refrigerator is staggering, then a third.party noise will occur during operation.

With reliable installation, the sound can make a compressor casing relating to the posterior wall of the tube, the contacts of the protective relay, the evaporator fan. To eliminate such situations, it is necessary to adjust the work of the corresponding elements.

Lack of lighting with an open door

If light bulbs do not burn in the refrigerator, then both lighting devices themselves could come out of the system and the alarm button about the opening/closing of the doors.

A separate reason may be the lack of power from the electric network. Therefore, before starting the repair of the refrigerator, it is necessary to make sure that the device is supplied to the device.

Water appeared inside or under the bottom of the refrigerator

Such an incident can be found in the form of a puddle under the refrigerator or as an accumulation of water inside the chamber. In most cases, it determines the following reasons:

  • Temporary power outage that you did not notice;
  • Someone installed in camera or not sufficiently cooled dishes;
  • Clogging of drain or tubes in the system with a crying evaporator;
  • Not tightly closed doors;
  • Inappropriate environmental conditions (ventilation of the premises, bringing the norms to the requirements of the plant is required).

The above list of malfunctions is relevant for those situations when the device retains the cooling temperature. If it does not freeze, the reason is due to other factors.

The appearance of an unpleasant odor

In addition to natural factors in the form of products with a specific smell, spoiled dishes and unwashed walls of the refrigerator, an unpleasant odor can occur due to burning of plastic, electrical contacts, isolation, etc.D. If in the first case it is enough to observe vigilance, then in the second there is a real threat of capital breakdown or even fire.

The red bulb is burning

Indicates that one of three breakdowns occurred:

No matter what the reason, the repair should not be postponed.

Step.by.step instructions for repairing nodes and refrigerator systems

After you have decided on the cause of the malfunction, you can proceed to eliminate it. Consider the most common options.

Elimination of a malfunction with a thermostat

Depending on the specific model, the thermostat can be located both inside the refrigerator and outside. With the internal location, it is enough to remove the temperature adjustment handle and remove the thermoregulator housing.

In the refrigerators Samsung, LG and other foreign brands, you can also check the thermostat under the panel of reducing and increasing the temperature of cooling. But it is placed on the outer side of the camera. You need to determine the performance:

    from the network;

  • Completely defrost;
  • Turn on the refrigerator for maximum freezing, placing inside the thermometer and wait a couple of hours, if the device shows not 5. 7 ° C, then the replacement is inevitable.

To fix the refrigerator, it is enough to purchase a spare part and install a new in return for a faulty part.

Search for leakage and replacement of a refrigerant

  • Soapy solution. available in the case of a weak leak and the presence of pressure of liquid refrigerant in the system. In this case, access to all pipes is provided. the protective cover of the case is removed, the evaporator is defrosted. At the place of gas release, the soap solution will foam.
  • Dye. is used where the pressure in the circuit does not allow the use of soap solution. The dye is added to the liquid freon and launched into the system, after which a characteristic color appears in the leakage site.

Before downloading a new gas from the system, the remains are pre.removed with a vacuum pump, when blocking the blockages, additional cleaning is carried out. Then the refueling is made. Experts recommend performing this procedure and without leakage every 3. 5 years.

Damage to thermal protection relay

In case of violation of the normal operation of the temperature fuse, a premature shutdown of the refrigerator may occur, which is why the threat of engine overheating occurs. For repairs, you will need to remove the relay and disassemble its body, if the reason is in the jammed rod, the issue can be solved yourself, if the winding is damaged, you will have to change the whole detail.

Replacing a faulty compressor

  • Turn off the refrigerator from the network;
  • Tilt the compressor and run the compressor for a couple of minutes;
  • The piercing valve is fixed to the filter-dryer, connect the cylinder to the valve and tighten the piercing valve and open it for half a minute;
  • Instead of a gas station, solder the copper tube;
  • Perform the incision on the capillary tube;
  • Remove the old compressor and install the plugs in the suction and pumping output;
  • Install a new compressor and solder it, carefully inspect the quality of the soldering.

Compressor repair

Elimination of rattling compressor sounds

The noise of the compressor can be caused by the loose fit of metal elements or vice versa, the excessive proximity of certain elements, which is why collision occurs and rubbish.

For repair, it is necessary to tightly fix the casing, in the case of a shaken fastener, put the washers for tight fit and tightening.

Compressor mounting adjustment (shown by arrows)

In case of approaching other elements, it is necessary to adjust the devices itself in the opposite direction or carefully bend the tubes if it is impossible to move the compressor.

Replacing lighting lamps

In order to avoid electrical injury, disconnect the refrigerator from the network. Then open the door and check the condition of the lighting device, for example, in the refrigerators Indesit, the light can be very hot, so you should wait for complete cooling.

To do this, it is not necessary to use the same lamp, but you can find an alternative replacement, but, accordingly, according to the type: incandescent or halogen. The power of the lamp should not exceed 30 watts. But before replacement, it is worth checking the voltage in the cartridge, because the reason may not be in the lamp at all.

Solving problems with temperature sensors

This part is designed to regulate the work rate of the compressor installation. When they fail, the refrigerator will not be able to maintain the desired temperature regime. Quite often, such a malfunction occurs in the Nord refrigerators, they include several such elements at once.

But to independently disassemble and repair at home they will not work, so after removing the sensor, it will require a complete replacement.

Cleaning the drainage system

There are two options for placing the tube. outside the housing and under it. In the first case, cleaning is performed quite simply: remove the phone and rinse it in hot water, soften the accumulated clogs if possible.

In case it is impossible to remove the phone, it should be tried to clean it with a ruff that is included in the kit. If it does not cope, a metal wire is used for repair, previously cleaned by sandpaper. After cleaning the tube, it must be washed with water.

Repair of a drainage tube

Alignment of the position of the doors

To adjust the situation, it is necessary to get to the place of fastening, for example, in the LG refrigerators you will need to remove the protective bar, in other models the bolts can be in the public domain. After unscrewing, remove the door, put the puck in the right nodes and set the door to place. If there are such, collect decorative designs in the reverse sequence.

Damage to control

Characterized by the complete silence of the refrigerator, despite the fact that the power chain is completely good. Control board is one of the very complex devices and one of the most expensive. Replacement in the service center will cost three expensive, so it is better to make repairs on your own. For this:

  • Turn it out of the outlet and expand, in the refrigerators of Stinol and many other brands, the board is located in the lower left side. This is how the control board is removed
  • Unscrew the fasteners A and remove the latch B;
  • After that, you can see the board itself in the case, carefully disconnect the terminals from.

How to get rid of unpleasant odors?

The appearance of unpleasant odors in the device is most often associated with improper storage of products (non.compliance with the rules of commodity, storage of damaged food and t.D.).

To get rid of the “aroma”, first of all, find out and eliminate the reason for its occurrence.

The following methods will help to eliminate the pungent smell from the refrigerator:

  • Mix vinegar with water in equal proportions and wash the internal walls of the camera;
  • Pull 20-30 tablets of activated coal, pour it on plates or in bags of gauze fabric, put the product inside the refrigerator;
  • The crushed crusts of citruses (lemon, orange), black tea, sugar, rice, vanilla, coffee grain (pre.chop them) are well “absorbed” (pre.chop them): as in previous cases, place the products in bags made of linen, gauze, put it inside the household devices.

Effectively eliminate even the most caustic smell of special balls for refrigerators, which are sold in household chemical stores.

The mineral components contained in them destroy the unpleasant “amber” and prevent the appearance of mold. The balls are valid for 3-4 months, after this period, the drugs should be replaced with new.

ADVICE! Do not forget to take care of the device if you need to leave for a long time: defrost, wash the device and leave it disconnected, with an open door.

Carry out a periodic check of products in the unit, throw out food, the expiration date of which has expired, store food in special containers closed with a lid.

The purity in the refrigerator is not only the key to your health, but also a long service life of kitchen appliances.

How often should the refrigerator No Frost should be cleaned

Technology manufacturers advise disconnecting it from tension and let it relax at least 1 time per year.

If you notice that the device began to coldly cold or malfunction, it is better not to wait for a specific time, but to defrost it immediately. Therefore, answering the question: “How often should I defrost the refrigerator No Frost”, we can say: as soon as a similar necessity arises. If you see that a thick layer of ice has formed on the walls of technology, then this suggests that defrosting is necessary on the same day.

The causes of the non.working freezer in the LG No Frost refrigerator

A number of breakdowns in which the freezer does not freeze have “additional” symptoms. We systematized them in the table so that you can independently narrow the circle of possible problems and find out the approximate cost of the upcoming repair.

Failures of the refrigerator can occur for a number of reasons:

  • Lack of tightness in the system. In the event that the freezer does not work due to gas leakage, the accident is eliminated by the detection of the damage site, the opening of the hole and the subsequent addition of the refrigerant to the system. In order to detect microcracks, special equipment is used.
  • Blockage in a capillary pipeline. This can happen for a number of reasons. In particular, the tube is clogged due to the clogging of the filter. As a result, the refrigerator camera does not perform its functions.
  • The zeolite cartridge clogged. As a result, the compressor can overheat and completely turn off. This leads to the fact that the freezer does not freeze. To eliminate the malfunction, a complete replacement of the filter is necessary.
  • Damage to the thermostat. The refrigerator camera may stop freezing if the thermostat gives irregular indicators to the processor. To eliminate the problem, you can try to adjust the temperature by raising it or lowering it.
  • NO FROST system malfunction. This can happen for various reasons. For example, the system clogged with frozen water, the evaporator froze, the fan was out of order. Methods of solving the problem depend on a specific problem. At the initial stage, it is recommended to completely defrost the unit. In this case, it is strictly forbidden to scrap ice from the walls. After 24 hours, the device can be turned on again.
  • Damage to the control unit. Program failure or full failure of the unit leads to the fact that the refrigerator camera ceases to perform its functions.
  • Also an accident, in which the frosts of the refrigerator does not freeze, occurs with problems in the operation of the compressor, engine, and the launcher.protective relay. Sometimes the situation arises that the motor works, but makes long pauses. As a result, the temperature in the chamber decreases. It can also happen for the above reasons.

MK does not freeze in the LG No Frost refrigerator because of the outlet-with your own hands

First of all, it is worth paying attention to the serviceability of the network fork, electric cable and the outlet itself. It is possible that the wires from the terminals were disconnected in the outlet or fork, or a cliff occurred in the cable veins, and this was the reason that the freezer did not work. Check the voltage in the network, if it is lowered, then the device will not turn on.

[LG Refrigerators] Door In Door Ice Maker Not Working

To check the outlet, connect any other electrical appliance into it. If he earned, then look for a reason in a fork. If the fork is in order, call the cable with a tester. Also, if when the device is connected to the network, the light does not light up inside it, then this indicates the damage to the cable. To check the voltage on the network, use the multimeter. To start the device, a voltage of 220 V is required.

MK does not freeze in the LG No Frost refrigerator due to an incorrectly exhibited mode-with your own hands

If you have a suspicion that the freezer does not turn off, then it is recommended to observe some time at the operation of the device. Normally, he should work in “one to two” mode, for example, 10 minutes work. 20 minutes rests. Time can also increase if the capacity of the unit is semi.empty, or the room is very high temperature. But when your observations confirmed that the device does not think to turn off, or the camera turned off over a long period of time, pay attention to the following points.

The optimal temperature option inside the capacity of freezers is considered to be indicators from.18 to.19 ° C. With the above higher values, the device will work without a break. Therefore, even if there is heat in the room, you should not exhibit too low temperature on the thermostat too low. The device will be easier to support the microclimate in the cell at a standard level than to achieve high indicators. Also make sure that the refrigeration equipment does not stand close to heating devices.

Perhaps the “Super.Summary” mode has been established. Old models after turning on this mode do not turn off automatically. Self.shutdown is available only to modern units.

Also, for example, in the freezer of the Stinol 106 brand, a timer is sometimes observed when the “Otvka” mode is established. While the unit does not turn on. But if you turn the ratchet for several degrees, then the device begins to work. The defect with the timer is explained by the fact that in the hourly mechanism there is a jamming of the gears. In the STINOL 106 Q model, this problem with the timer is also present.

MK does not freeze in the LG No Frost refrigerator due to the wear of the seals on the door-with your own hands

Over time, with prolonged operation of the freezer, the rubber seal on the door can crack, deform, stratify or rub out. As a result, the door does not fit tightly, the inner capacity of the device is not cooled enough, due to the constant leakage of the cold, the compressor works without stopping and quickly wear out.

The ATLANT freezer will not leave you a chance to miss the wear of the gasket. If you see that the red bulb is burning, then the temperature rises in the chamber (possibly due to a bad fit of the door). If a green light caught fire, it means that the temperature is normalized. If the wear of the seal is detected, the fact that the unit is poorly freezed, as soon as possible, try to replace the rubber gasket. How to restore the seal on your own, is told in this video

MK does not freeze in the LG No Frost refrigerator due to the failure of the details-with your own hands

If the situations listed above are excluded, and the freezer still does not work, it means that some kind of structure is out of order.

MK does not freeze in the LG No Frost refrigerator due to the failure of the engine-compressor-do it yourself

If you are the owner of a single-engine unit, then when a motor-compressor breakdown, the cold will be absent in all departments. If only the freezer stopped freezing, and the refrigerator works, then the device is equipped with two compressors. In this case, the engine of the freezer usually starts for 3-5 seconds and turns off. Causes of malfunction:

A malfunction of the electric circuit

And such a reason can start noise or rattling. The launcher can come out of the system, then the refrigerator acts very aggressively. not only growls, buzzes and hisses, but also awaits you with a quick and sharp shutdown. The relay will have to be changed, only a specialist should do this.

Another possible option for a breakdown, why the refrigerator buzzes, hits and generally works noisily. these are burnt windings of the fan electric motor.

Perhaps a short circuit or resistance leak. It is checked by a tester. And you can remove the problem only by replacing the engine. Although in some cases you can dry it well, but it does not always work.

Preparation for the transportation of the LG refrigerator in the car

Regardless of the position in which you are going to transport the refrigerator: in horizontal or vertical, it is necessary to carefully prepare for this “operation” so that the transportation does not lead to the failure of the unit. The preparation should be carried out in the following order:

Defrost and dry the refrigerator (of course, all products need to be removed from it).

Remove all the boxes and shelves from the unit. They must be packaged separately, shifting with paper or a rag. They can also be fixed inside the chambers using special fixators, if they are preserved (usually the manufacturers of refrigerators use it).

Fix the compressor. Some manufacturers equip it with special transport bolts. they must be tightened. If the screws are absent, it is necessary to fix the compressor using cardboard or mounting foam.

Fix the refrigerator doors. You can use tight belts, rope or masking tape for this purpose.

Pack the unit. Before transporting, the refrigerator must be wrapped in several layers with a special air.pussy film or thick paper. The ideal option is to pack the unit in factory packaging if it is preserved.

After the above manipulations, you can proceed to loading and transporting the refrigerator.