Step.by.step instructions on how to remove the upper cover of the Indesit washing machine

In the case of the cut of the tank, a hacksaw with small teeth, a long drill drill, bolts or screws, a pistol for sealant will come in handy. It is advisable to stock up in advance tools.

This device is even easier to disassemble than a front loading machine. To remove the top cover, use a screwdriver: Paturate the spare part on both sides and pull up. After that, tilt the plastic part to yourself and remove.

Often, in addition to dismantling the upper panel, you need to remove the rest. Consider how to remove the front and side panels for this type of load. Basic actions:

  • unscrew the screws by preserving the filmed goals for grounding the housing;
  • Bend the wall below, moving it vertically to the floor;
  • Remove the side panel;
  • Having done similar actions, we remove the second sidewalk;
  • To dismantle the front panel, unscrew the screws to which access.

To assemble a machine, take disassembled elements and repeat the actions in the reverse order.

You can disassemble equipment with frontal or vertical loading with your own hands, the main thing is to use the recommendations and complete the preparatory work slowly. You can also watch the video if there are doubts or questions how and with what tools to remove the upper plastic cover of the washing machine. The correct operation of the equipment and washing without failures depend on coordinated actions. If even after the video you will not be able to carry out dismantling, use the services of a professional master.

How to dismantle the front?

After the washer cover is dismantled, you can start analyzing the front panel.

Work is carried out in several stages. First of all, the lower part of the front cover is removed. To do this, open the hatch hiding the garbage filter and twist the screws located at the corners of the niche. Then, carefully picking up a flat screwdriver of the latch on the right and left side of the decorative bar, we pull it over.

To remove the upper part of the front panel of the LG washing machine, it is necessary to carry out a number of consecutive actions:

Remove the dispenser for detergents (click a special latch inside the tray and pull the powder receiver on ourselves).

The final stage is to unscrew two screws on top and four in the lower part of the front panel, and then remove the lid from the body of the washing machine.

Replacing the bearing in the bathing machine Indesit with your own hands

Before changing the part, prepare for disassembly. What tools are needed:

  • Cross and slotted screwdrivers.
  • Horn keys.
  • End heads and keys.
  • Wooden bar.
  • Bit.
  • Pliers.

WD-40 liquid is also useful. She will help to cope with the bitten mounts.

Replacing the bearing of the Indesit washing machine provides for a complete disassembly of the technique. This requires free space. If there is no way to demolish the machine into the garage, then put forward the body to the center of the room.

remove, indesit, washing, machine, list
  • Pull the plug out of the outlet, turning off the car from the network.
  • Cross the water supply valve.
  • Disconnect the pouring hose from the body. Immediately lower it into a sink or water drain container.

Put the smell in the center of the room. Remove the dispenser for the powder because the remaining moisture accumulates inside it. Also pull the drain filter.

It is located under the loading hatch. Wait for the drain of liquid and proceed to disassembly Indesit IWSC 5105, Wisl 102.

Dismate the top cover, twisting two screws from behind. Put it back, remove it to the side.

  • Twist the screws of the control panel. Leave it hanging on the wires or laying up the case.
  • Remove the electromagnetic valve bolt from behind. Remove it with the bunker of detergents. In parallel, lift the cloth of the pipe and remove it from the seat of the tank.
  • Disconnect the interference filter by twisting the rear fasteners.

Go to the back cover of the Indesit Wisl 103, Wisl 83 or other model.

  • Disconnect the heating chips. It is not necessary to get a part. But you can do this to clean the heater from scale. Twist the central nut, sell the bolt inward and take out the heater.

Turn the machine to the side. You can put an old blanket or towel on the floor in advance, so as not to scratch the body. Shock absorbers are attached to the lower part. Unscrew them.

  • Disconnect the terminals from the pump.
  • Eliminate the click of the drain pipe, pull it off the tank. Water accumulated inside, so direct the pipe into the container or on the towel.

Nothing else is attached to Baku from below. Put the machine “on your feet” and switch to the front wall.

The dismantling of the front panel begins with the removal of the clamp of the hatch cuff.

  • Remove the screws ub.
  • You can immediately run your hand to the body and pull out the wiring of the ubble.
  • Remove the fixing screws around the perimeter of the wall. Raise it up and remove it.

Soon we will come to how to pull out and replace the bearing in the smell Indesit Wisl85x, WS84TX. In the meantime, take out the tank from the body. Raise it, removing it from the springs.

Features of disassembling the tank. This element in the Washing machine “Indesit” is non.vegetable. Install it on the rib, prepare a hacksaw for metal. There are several features of sawing that will help you tightly collect halves in the future:

  • Speaking is carried out from top to bottom up to half. Then you need to return up again and saw the other half.
  • The hacksaw is installed strictly evenly. If you place it under the slope, there will be a leak.

Before the cutting, scheme places for future holes. Then self.tapping screws for fastening two parts will be placed there. Drill holes of the right diameter with a drill. Read more about how to cut the tank, read in a separate article.

After the upper part is removed, proceed to the dismantling of the pulley.

This is necessary to get the drum. Blok his rotation with a wooden bar. Throw the key to the central bolt and unscrew it.

To knock out the drum, tap with a rubber hammer on the sleeve.

How to remove a bearing with a smell “indesit”?

  • On the outer ring, set the chisel. Rearranging his cross-on-cross, tap with a hammer.
  • You will have to knock out two elements: internal and external.
  • After that, clean the seat from scale, dirt, production.

Install the part from the reptile to the nest. With the same movements as during dismantling, clog bearings to places.

A seal is placed on top. Watch the video of the work:

At the end of the work, assembly is carried out. After installing the drum, grease the edges of the tank with a sealant. Fighting them tightly. Then tighten the screws into the prepared holes.

Sometimes you need to replace the engine bearing in the washing machine. You can determine the breakdown by poor rotation of the motor rotor. During work, the sound of scratching, creak is heard. This means that driving details have worn out and a replacement is required.

How to change products? For dismantling, you will need pullers. You can buy them in the store, just make sure that they approach the size of the shaft. Install the puller and pull the ring from the place. To facilitate the task, grease the WD-40 liquid mount.

The new part is evenly clogged on the shaft.

That’s all. Work is painstaking and requires skills in repair. But there is nothing complicated for a person with skillful hands. Good luck!

How to remove basic details

The washing machine consists of many parts, most of which are hidden inside the case.

Here is a schematic image of the main details of the washing machine

We begin to disassemble the case from the top panel, which is attached with two bolts located from the back of the machine, they must be unscrewed first. Then, standing on the front side of the unit, pull the panel over yourself and slightly lift.

Next, go to the back panel, which holds on six self.tapping screws. You can unscrew them with a screwdriver. Directly behind the lid you will see a drive belt, it is better to remove it too, carefully scrolling the pulley wheel clockwise.

The diagram shows which way you need to rotate the pulley in order to remove the belt from it

To dismantle the dashboard, unscrew several screws located in the niche of the tray for detergents. Then we disconnect the wires and the pipe, remove the panel from the latches and remove it to the side.

In the process of disassembly, the location of the parts and the contact connection scheme can be photographed so that after the repair it is quickly and correctly assembled in the reverse order.

In the upper part of the washing machine are located: counterweight (stone), a pipe connecting the compartment for powder with a tank, a water fence valve and its contacts, as well as a press, its tube and contacts. We remove all these details.

Before cleaning the front panel, remove the hatch door and rubber seal. We start dismantling with a cuff. bend it with a screwdriver and carefully remove it. We dismantle the door, unscrewing several bolts that hold the loop. Then we remove the screws that hold the front panel, and remove it to the side.

Rubber cuff is removed, carefully bent with a screwdriver

At the bottom of the unit, you need to dismantle an electric motor, tubular electric heater (TEN), a lower counterweight, a drain pipe and shock absorbers on which the tank is held.

It is easy to find the heating element at the end that is visible under the tank. Remove the entire wiring from the heater contacts. Unscrew the nut located in the center between the contacts. Having shook the element, we remove it from the groove. Remove the power chip and ground wire from the engine, and then unscrew the bolts fixing it.

The heater is located under the tank to remove it, you need to disconnect the contacts and unscrew the nut located in the center

To remove shock absorbers and a drain pipe, you need to put a washing machine on the side. Using the pliers, remove the clamp and disconnect the drain pipe from the pump. Then unscrew the shock absorbers.

To dismantle the drain pipe, you need to loosen and remove the clamps holding it

After dismantling all the details, we take out the tank. But what to do if this is not enough? How to disassemble the drum of the Indesit washing machine, located inside a non.vegetable tank?

How to disassemble tank and drum

The washing machines of the Indesit trademark of the tank are usually non.vegetable, that is, when failing of any element located inside, the manufacturer recommends changing the part entirely. Such repairs can be expensive, so if it is necessary to replace, for example, a bearing, it is still better to disassemble the tank.

In the photo you see an unusual tank of the washing machine in which the drum is located

Dismantling begins with the fact that they remove the pulley (the wheel through which the belt passed). The bolt that fastens this detail experiences significant loads, and it is important that it holds tight. Therefore, often when assembling the machine, it is not only twisted, but also additionally fixed with glue. It is better to use a hexagonal key type “Zvezda” T40 size and loosen the bolt, gradually loosening it. If the part is not amenable, we spray it with a WD-40 tool or neatly knock it down from the glue with a hammer.

remove, indesit, washing, machine, list

In order to unscrew the bolt fixing the pulley, you need to use a hexagonal key type “Zvezda” size T40

Then we lay the tank on the side and carefully saw with a hacksaw along the seam (where two halves of the details are soldered). Pre.drill the hole along the entire perimeter of the hole (during the assembly of the half can be easily fastened with bolts).

When the tank is open, unscrew the bolts attaching the drum, unfasten the mounts and remove the tank wall. Now you can disassemble the drum, that is, get an oil seal and bearings from it.

Start with a bearing located closer to the outer part of the drum. We lay the part with the hole with the hatch down, set the chisel on the outer rim of the metal ring and hit it with a hammer.

To remove the bearing from the drum, you will need a hammer and chisel

We carefully monitor the position of the bite when knocking out the bearing. if the tool slides, and the blow will have to be on the inner ring, it can fly out and it will be quite difficult to remove the rest of the bearing from the nest. We dismantle the inner bearing in the same way, and then take out the oil seal.

How to remove basic details

The washing machine consists of many parts, most of which are hidden inside the case.

Here is a schematic image of the main details of the washing machine

We begin to disassemble the case from the top panel, which is attached with two bolts located from the back of the machine, they must be unscrewed first. Then, standing on the front side of the unit, pull the panel over yourself and slightly lift.

Next, go to the back panel, which holds on six self.tapping screws. You can unscrew them with a screwdriver. Directly behind the lid you will see a drive belt, it is better to remove it too, carefully scrolling the pulley wheel clockwise.

The diagram shows which way you need to rotate the pulley in order to remove the belt from it

To dismantle the dashboard, unscrew several screws located in the niche of the tray for detergents. Then we disconnect the wires and the pipe, remove the panel from the latches and remove it to the side.

In the process of disassembly, the location of the parts and the contact connection scheme can be photographed so that after the repair it is quickly and correctly assembled in the reverse order.

In the upper part of the washing machine are located: counterweight (stone), a pipe connecting the compartment for powder with a tank, a water fence valve and its contacts, as well as a press, its tube and contacts. We remove all these details.

Before cleaning the front panel, remove the hatch door and rubber seal. We start dismantling with a cuff. bend it with a screwdriver and carefully remove it. We dismantle the door, unscrewing several bolts that hold the loop. Then we remove the screws that hold the front panel, and remove it to the side.

Rubber cuff is removed, carefully bent with a screwdriver

At the bottom of the unit, you need to dismantle an electric motor, tubular electric heater (TEN), a lower counterweight, a drain pipe and shock absorbers on which the tank is held.

It is easy to find the heating element at the end that is visible under the tank. Remove the entire wiring from the heater contacts. Unscrew the nut located in the center between the contacts. Having shook the element, we remove it from the groove. Remove the power chip and ground wire from the engine, and then unscrew the bolts fixing it.

The heater is located under the tank to remove it, you need to disconnect the contacts and unscrew the nut located in the center

To remove shock absorbers and a drain pipe, you need to put a washing machine on the side. Using the pliers, remove the clamp and disconnect the drain pipe from the pump. Then unscrew the shock absorbers.

To dismantle the drain pipe, you need to loosen and remove the clamps holding it

How to Replace a Heater Element on an Indesit Washer Dryer

After dismantling all the details, we take out the tank. But what to do if this is not enough? How to disassemble the drum of the Indesit washing machine, located inside a non.vegetable tank?

Instructions for analyzing the Washing machine Indesit

Not a single automatic washing machine is insured from various malfunctions. And Indesit machines are sometimes characterized by such breakdowns that require it almost complete disassembly. For example, replacing bearings. Of course, the disassembly process is quite laborious, but quite accessible for independent implementation. Often there is simply no point in paying money to the service (and considerable). And therefore, consider the process of disassembling the automatic washing machine Indesit with your own hands. All by points.

Preparation for disassembly

  • A set of different screwdrivers. A pair of cross.lengths of different lengths. Flat screwdriver. It will be needed in order to push various clamps and fixers. Take with a set of bit. hexagons and stars.
  • A hammer. It will be needed if the replacement of the bearings is needed.
  • Pliers.
  • A set of keys.
  • A block of wood.

We proceed directly to the disassembly of the Indesit washing machine.

Remove the top cover. You need to unscrew a pair of screws from behind and pull back. Not up, but back. Otherwise you can break plastic latches. We see a balancing weight on top. It looks like a concrete stone fastened with nuts. We take the key with the head of the desired size (usually by ten) and unscrew the mounts. Now we take off the load itself.

At the next stage, you need to remove the front panel of the Indesit washing machine. To do this, first we take out the cuvette for powder and air conditioner. It must be pulled to the stop, slightly lifted and pulled out of the grooves. Access to the panel mount screws opens. Take the cross screwdriver and remove them. Remove the front panel. Depending on the main goal of disassembling the Indesit washing machine, you can leave the panel hang on the wires or disconnect completely. But you need to remember or write down how contacts were connected.

Now it’s time to remove the dispenser for powder. In the Indesites, it is quite large. from the front wall to the filling valve on the rear. Disconnect the wires (and remember again or mark the connection by the color of the wire). Near the entrance for supplying water on the back panel, unscrew the screw. Disconnect the rubber pipe from the dispenser. You need to pick up the rubber loop of this pipe and remove it. Remove the dispenser (or powder receiver. as you like). Remove the water level sensor.

Finding it is not difficult. This is such a round thing with wires installed on the case. It will interfere with further extraction of a tank with a drum. Turn off the wires. The sensor is attached to the clip to the body. Slightly pull it with a flat screwdriver and squeeze the latch. Using the pliers, disconnect the hose to below. You can also remove the network filter. It is connected to the power cord of the washing machine. Move on.

It is necessary to remove the rubber cuff, which is installed between the tank and the lamp of the washing machine. She holds on a spring clamp. The spring is carefully pulled and removed. Now the cuff can be separated from the body.

The following manipulations will be carried out at the bottom of the Indesit washing machine.

The back cover is already open and at the bottom of the tank the outer part of the heater is clearly visible, to which the wires are brought. Disconnect the contacts from the heater and engine. Immediately you need to separate the bunch with the wires from the tank body. You can remove the heating element after extracting the tank, or you can at once. Unscrew the fasteners that are located between the contacts and carefully pull. We use swaying movements.

We disassemble the drainage system. Open the lid under which the drain filter is hidden. We unscrew two screws with which it is attached to the body, and pushed inward. Now you can put the washing machine to one side. Remove the pipe connecting the filter and drain pump.

In this case, water will pour out of the pipe. It is worth stocking up in advance with a capacity to collect it. The pipe is removed using pliers. You just need to weaken clamps. Then the pump is removed directly. You need to unscrew the screws with which it is attached and remove the wires. If necessary, the pump is also easily disassembled.

Unscrew the fastening of shock absorbers on the bottom of the washing machine. We carefully check. the tank must be freed from all connections with the body.

We raise the car to the usual position. Do not forget that the lamp of the washing machine should be open. Now the tank is just hanging on springs. Take them for them and pull out the tank out with the motor and front load.

We share the tank and engine. I will have to unscrew a couple of bolts by ten and carefully tinging a flat screwdriver to separate the motor from the tank.

The concrete balancing load is fixed with screws with a configuration in the form. We remove with the help of the corresponding tool.

Remove from the “body” of the tank of the washing machine all the details. shock absorbers and pipe. Shock absorbers are held on plastic pins, and the pipe on the clamps.

What we have in the end. an empty body of the machine and the tank, with the drum installed in it, separately.

How to remove a drum from a tank.

We get two halves. one empty and the other with the drum. Using a bolt (desired size and thread) and a hammer, the drum is neatly knocked out of the bearings in the tank body. Faulty bearings are extracted and new.

The task was completed. the Indesit washing machine is disassembled. Until absolutely complete result, you can still remove the door of the hatch from the hinges and disassemble it and it. All subsequent assembly is carried out in the reverse order. The integrity and tightness of the tank is restored quite simply. Holes are drilled in halves. The joints are coated with silicone sealant. The whole structure is tightened with bolts.

How to remove the lid correctly

When the preparation is completed, you need to proceed directly to disassembly. You can do this, knowing the type of loading machine. Naturally, if you are your machine, then this item can be missed. There are two types of loading: frontal and vertical.

The main goal of dismantling the upper part of the equipment is to replace the non.working part.

The list of tools of striking differences will not have, as well as the preparatory stage of work. So, consider the instructions for disassembly in both cases.

remove, indesit, washing, machine, list

Removing the cover on the front model

So, we proceed to the opening of the upper cover. It is important not to forget about the problem with the latches, do not damage them. There are a list of which washing machines that the upper cover is removed, but basically this instruction can be used as a universal.

So that there are no difficulties with full analysis, we recommend that you adhere to the instructions.

  • Inspect the rear panel for the presence of two screws. They play the role of the upper cover lock in the washing machines of the front.type indesit type.
  • Remove them. You can do this with a screwdriver, often with a cross.shaped nozzle.
  • Being behind the washing machine, raise the lid, simultaneously pulling it to you. This stage should be carried out carefully, despite the fact that you will need to make efforts. Pull the lid until the latches are weakened.
  • The cover may not give in. It is impossible to make excessive efforts in this case (remember the delicacy of handling handling). It is better to try to remove it from the other side. the front. Only you need not to pull to yourself, but pressing to push forward (to the back).

Follow the instructions for disassembling the washing machine.

Note! In no case do not listen to the recommendations to put the lid with a knife for opening. This can create extra problems!

Do not damage parts of the machine during repair.

Removing the lid on the vertical model

It is important to know that vertical loading is more difficult to disassemble. Here, the removal of the dashboard is added to the process of dismantling the cover.

You can disassemble equipment with vertical loading with your own hands.

The role of physical intervention plays the role. It can be reduced to attempts to get to the hatch door, then everything will be limited to twisting a pair of fixers.

indesit washing machine how to resolve bilking light

To remove the top cover, use a screwdriver.

But it will be possible to remove the upper panel only by dismantling the control mechanism. The chronology of actions is as follows:

  • We find self.tapping screws under the dashboard and twist them;
  • You need to tilt the panel forward to remove (perform this action carefully so as not to damage the mechanical elements);
  • The lid is held by the screws located under the dashboard, they must be unscrewed;
  • Remove the lid.

Note! The wires are brought to the panel, do not damage them when removing.

Different models have differences in the repair.

Vertical and other mounts

There are models of the “older generation”, from which the upper part is removed differently. For example, the ardo machine is arranged differently. In order to open it, first you need to remove all the bolts fixing the cover from the back. Gently unscrew the screws and raise it, slowly moving back, but forward. The trick is that the “roof” will go only at an angle that you need to feel, pry it in time.

Old models from Siemens and Bosch have specific mounts, which are now not on modern machines. They are located on the side of the upper cover. First delete all the plugs, and then start to twist the bolts. Disconnect the cover also. at a certain angle, otherwise it will be impossible to remove it.

Removing the lid from the washing machine with vertical loading is much easier. You need to put it with a flat screwdriver and carefully pull it up. It remains to tilt the element forward and remove it. It happens that, having removed the upper panel, a person is faced with the need to remove the front and lateral parts. For this you need:

  • unscrew all the bolts by preserving the washers (they are needed in order to ground the case);
  • bend the lower wall;
  • shift it vertically;
  • Remove the panels located on the side;
  • Witch the side screws and remove the front panel.

After establishing the cause of the breakdown, make all steps in the reverse order.

Dismantling Scheme of the Washing machine “Indesit”

Start by disconnecting communications and draining water. Even if washing is over long and the tank is empty, water still remains inside the case. When transporting or tilted, cm liquid can enter the electronic parts of the machine, which will lead to expensive repairs.

  • Prepare an empty container.
  • Disconnect the car from the network.
  • A fence hose is attached to the back panel. Disconnect it from the body. Substitute the container, water can pour from the hose.
  • Return to the main panel.
  • Below, under the loading hatch there is a small door.
  • Open it.
  • Twist the filter cork counterclockwise.
  • Drain the water.

It is also better to immediately get a dispenser for powder. To do this, press the central latch and pull out the tray.

Put the case to the center of the room. There should not be a carpet on the floor, you can only stretch an unnecessary towel in case you have to turn the machine.

Take a look at the disassembly scheme for cm so that it is clear where what part is located:

How to remove the top cover? To disassemble the equipment with your own hands, the upper panel is initially dismantled. Using a screwdriver, twist two screws from behind. Move the lid from yourself, remove from the place. Immediately take out the upper counterweight. Unscrew the bolts with which it is attached.

Now it is possible to disable the control panel. Remove the screws around the perimeter, unfasten the latches. If you want to completely remove the panel, then pull the wiring chips. You can just leave it hanging on the wires.

How to remove the back cover? Remove the screws around the perimeter of the back wall. Set her aside.

Remove the belt from a large pulley, and then from the pulley of the motor. Now we dismantle the engine:

  • Ten is located under the tank.
  • It is not necessary to get it, you can remove the tank along with the element. Check the heater with a multimeter for serviceability. If the spiral burned out or broke off, then turn off the contacts. Then twist the heater nut and sell the bolt inside. Put the part with a screwdriver and remove.

Rusty streams on the back of the tank. these are traces of the bearing. Replacement is required.

At this stage you can remove the pulley. We disassemble the fastening carefully:

  • Lubricate the central bolt with WD. 40 liquid. Often it is fastened with sealant, so you just can’t get it out.
  • Fix the pulley in one position with a wooden bar.
  • Tap the bolt, unscrew it.
  • Remove the wheel by pulling yourself.

Front wall. Now go in front of the washing room. Upper and basement panels are dismantled. It remains to remove the main wall.

Return to the upper part. To remove the powder receiver bunker, weaken the column of his pipe, which leads to Baku. Pull it out of place and remove the bunker. Now see what other details are attached to Baku. Remove the wiring and hose of the press. The hose serves to measure pressure and control the level of water.

It remains to dismantle the lower elements. Getting to them is easier through the bottom. The cooked towel is just useful. Put the automatic machine “Indesit” to the side. Usually the bottom is not covered by anything.

  • Using pliers, unfasten the cloth of the drain pipe. Remove it from the place.
  • It remains to pull out the dampers.
  • Remove the lower and upper mounts of the parts.

To get the tank, lift it up, removing from spring-suspension springs.

How to get to the drum and bearings? If you need to change the bearings, then install the tank vertically on a flat surface. Take a hacksaw for metal and begin to saw in the place of fastening of the seam.

Speaking is carried out as carefully and evenly as possible. In the future, these two parts will have to glue.

As soon as you get two separate halves, knock out the drum. Install a bar on the shaft and knock out a drum with a hammer with light tapping with a hammer. Now you can install new oil seals and bearings.

To provide further convenient disassembly, drill up to 6 holes under the perimeter of the halves. When assembly, the tank is twisted with screws and fastened with sealant.

How to disassemble the Indesit washing machine with the upper load?

Initially turn off the car from the network. For dismantling the upper cover:

  • Remove the inlet valve. Disconnect the hoses, wiring, remove the mount.
  • Twist the side panels of the side panels on the side, remove them.
  • Now access to fasteners of the front wall has opened. Remove the bolts and walls.
  • The heater is pulled out in the same sequence that is described above.

It remains to remove the drive belt and the pulley of the washing machine. The task of disassembling the washing room with the upper load is not easy. The case is narrow, all parts are tightly located. Therefore, you have to act by touch.

So you can independently repair the technique. We recommend the sequence of work to shoot on the video to repeat the assembly exactly.

Dismantling of a washing machine with vertical loading

Immediately note that the mechanism of Indesit devices with vertical loading is more difficult than with frontal, so we do not recommend that you independently disassemble it completely. In this case, you will need to lead it to the service center. However, there are a number of small malfunctions, the repair of which can be performed independently.

How to remove the lid of a washing machine with horizontal loading

So, we turn off everything, move away from the wall. Remove the two screws in the back and the upward movement remove the control panel, disconnect all the terminals, having previously photographed them with the phone so that there are no difficulties with their connection. Under the control panel there are four self.tapping screws on which the fastening of the upper cover is held: two on the right and two on the left. Unscrew them, and the lid is easily removed upward. Attention! Two self.tapping screws in the middle we do not touch! They fasten the drum. Most often the lid is removed due to its poor fixation.

The second problem, which is why it is necessary to remove the top cover is the loss of the tightness of the silicone sealing ring and, as a result, seeping water into the washing machine, which is fraught with closing the wiring.

Removing the lid of the washing machine, you can pull out the silicone cuffs and smear it with a special sealant.

If there are problems with the electronic board of the washing machine, it is necessary to remove it by unscrewing three screws. For this, a screwdriver with a star is suitable. Pre.disconnect all terminals from the board. After that, it can be attributed to the workshop, saving funds for disassembling and transporting the device.

Conclusion: of course, in every business a professional needs, and calling the Masters for the repair of the washing manna is much easier and more reliable, saving themselves from unnecessary headache and unforeseen circumstances during dismantling. But in order to save money, and having skillful hands, it is quite possible to repair minor malfunctions on your own.

How to remove the machine cover with vertical loading

Experts note that a vertical loading machine is easier to disassemble than from the frontal. It will be necessary to use the screwdriver to put the lid on both sides and pull up. Then tilt the part to yourself and carefully remove. Usually there are no difficulties with this.

If more complete repairs are required, other elements of the Indesit washing machine will be removed. You need to adhere to a certain order of actions.

  • You need to unscrew the screws and remove the goals that are used to ground the housing.
  • You should bend the wall below, carefully moving it vertically to the floor.
  • Now you can remove the side panel. first one, then the second.
  • To dismantle the front panel, unscrew the screws. Before that there was no access to them.

To assemble a machine, you need to act in the reverse order. The main thing is to ensure that all the screws are screwed.

It is not difficult to disassemble equipment with vertical or front loading, so often people can handle it on their own. It is important to carefully follow the instructions and carefully handle the device. Only in this case you will not have to worry about the fact that the Indesit device will not work fully.

Nuances when working with washing machines

Removing the top cover is usually not difficult, but still one should take into account certain points. With Indesit Wisl 105 machines and other models are easy to handle, because they have the same principle of analysis. Models are rarely found that are versed a little differently. Suppose an ardo manufacturer produces cars that have an atypically dismantled upper covers. You need to remember this, since you can face an unusual model.

As always, you will have to disconnect the device from the network first. Just in case, it is better to put on rubber gloves to avoid shock. After that, the unit will need to be moved away from the wall. You need a place to work, otherwise it will be difficult and even impossible to unscrew the screws.

The lid will have to be pushed back not back, but forward. That is, if a person stands behind the unit, then you need to move the element from yourself. The lid can be shifted only under the slope. Otherwise, nothing will work out. The angle will have to be determined independently, as it may differ. It is worth trying to make a different slope until you get a result.

On old washing machines, there are sometimes bolts fixed on the front panel. This is even more convenient, because there is no need to move the unit. All screws are covered with plugs that first need to be removed. After that, you need to spin the bolts, remove the fasteners and raise the lid, moving forward.

As a rule, Indesit machine models are versed according to the standard scheme. People have no problems in interacting with the device. It is worth acting carefully so as not to damage the plastic element. In addition, you need to try not to leave scratches. Then it will be hard to remove from the front panels. If you follow the instructions, it will be possible to independently remove the cover from the Indesit washing machine. The main thing is to correctly return it to its place, so that then there are no problems with the functioning of the device.