The dishwasher stopped typing water: the causes and ways to eliminate the malfunction

Today the most important assistant to the housewife in the kitchen is a dishwasher. The home unit is able to clean the dirty dishes of various types. But as with any household appliances, various problems can also happen to it. Often, owners of equipment are faced with the fact that the dishwasher does not get water. This may indicate both serious breakdowns and minor defects, or errors with connection.

Currently, the technique of various manufacturers is used in everyday life. Ariston, Bosch, Beko, Siemens, Aeg. They differ from each other with technical parameters. dimensions, capacity, power, energy consumption and various work modes. Despite this, the principles of work are generally approximately the same, so you can consider the same reasons because of which water does not enter the machine.

The most common reasons for the failure of the dishwasher are:

  • malfunction or incorrect connection of the intake filter;
  • clogging of internal water filters;
  • door malfunction;
  • incorrect operation of the water level sensor (press start);
  • malfunctions of the control system.

The brand of the dishwasher, as already mentioned, does not play a special role. The causes of breakdowns are usually approximately the same, so you can consider the days and the same options, as well as repair methods.

However, some models of cars, usually more modern, are equipped with Aquastop system. It represents a system of protection against leaks. The hose through which water enters is covered with a protective casing. In the event of an accident, the system is able to block the water supply. In some cases, the system malfunction of the AKVASTOP system prevents the water to get into the dishwasher. This option also cannot be discounted.

See also. tablets do not dissolve in the dishwasher. what to do?

Why doesn’t water enter the dishwasher?

Usually a breakdown of household appliances can seriously scare, but you should not worry ahead of time. On their own, it is quite possible to establish the main causes of a malfunction of their own technology, if you approach this issue correctly. Most often, the technique does not work due to the fact that the hose is incorrectly connected through which water enters inside.

If the machine worked properly for a long time, and then suddenly does not pump water, then the whole thing can be in clogged filters. Dirty accumulates in the tubes that prevents water from entering.

Sometimes the owners of the equipment do not notice that the water hose is transmitted by something or the front door simply does not close closely for some reason. The unit itself only buzzes and refuses to run the cycle. Such little things can seriously spoil the impression.

In what cases the dishwasher does not get water

Sometimes situations arise when a dishwasher cannot dial the right amount of water in a certain period of time set by the manufacturer (for example, 10 minutes). In such cases, PMM stops the work, sometimes buzzing, and on the display reflects the alphanumeric-cyphpical error code. For example, Bosch and Siemens dishwashers signal the E3, E8 or E15 codes such an abnormal situation.

E3 and E8 errors appear when PMM does not gain water

The liquid may not enter the reservoir of the dishwasher for reasons that simply find out and eliminate independently:

  • There is no water in the water supply or its pressure is very small. Determine this is simple. turn on the tap in the bathroom or in the kitchen.
  • A shut.off tap tap, located at the entrance to the apartment or at the output of the tee, through which the liquid is supplied to the dishwasher is closed.
  • Careless handling with the door led to the fact that the blocking sensor did not work. In this case, the liquid will not be supplied to the PMM until the door is tightly closed.
  • Pour the flood hose through which water enters the dishwasher. This can happen due to rearrangement of furniture or for other reasons. Checking and restoring its patency is quite simple.

If you pull the flood hose, it will overheat and will not let water pass

In the listed situations, restoring the supply of water and the performance of PMM are quite simple, and everyone can do this. But there are more complex problems, the elimination of which requires certain knowledge and skills:

  • Closed a flowing or input filter of rough cleaning. As a rule, the intake filter element is located at the junction of the pouring hose with the body of the dishwasher.
  • The Aquastop protective module that overlaps the water supply, if the liquid leak (error code in the PMM Bosch, Siemens. E15) has occurred or output.
  • The device blocking the front door of the dishwasher stopped working. In this case, the electronic control unit (hereinafter referred to as the ECU) does not receive a signal about the closure of the door and stops working.
  • The inlet valve does not open (the breakdown can be caused by blockage or hydraulic boom in the tap system). Perhaps there is no control signal from the ECU.
  • The water level sensor in the PMM tank (hereinafter referred to as also. Pressostat) is faulty. He can give an erroneous signal that the liquid has already been gained.
  • The electronic control unit of the dishwasher has failed and does not give out a control signal to open the inlet valve.

Bosch has worked in the Bosch dishwasher, which reports a water leak (E15 error code)

Trouble-shooting

Unfortunately, not all of the above damage can be eliminated with your own hands. For example, there are many details on the control unit’s board, each of which has a certain set of functions. Only a qualified specialist will be able to find out the reason for the inoperability of the ECU and repair. In addition, special equipment will be required to diagnose.

Printed circuit board of an electronic control unit

It’s good that the ECU malfunctions are not as common as those defects that will be discussed below.

Checking and cleaning inlet filter

It is unlikely that you can call clean water flowing from cranes. It includes many impurities, including solid particles of various shapes and sizes. PMM input filter protects the equipment from garbage, which water can spread through internal details. Connecting additional running filters at the input of pouring hoses provides more thoroughly liquid cleaning. These filter elements are subject to periodic cleaning.

The input filter is located at the junction of the inlet hose with the PMM case

To clean the input filter of dirt, do the following:

  • Crush the shut.off valve, disconnect the intake hose and drain water from it.
  • Pull the filter and rinse thoroughly under a stream of water.
  • Return all the details to your place.

Similar manipulations must be performed with a running filter if you have it installed.

The Aquastop module worked or broke or broke

Aquastop system today is equipped with the majority of PMM models. If an E15 error is displayed on the display, this means that water appeared in the pallet. The reason may be depressurization of the camera, water tank or one of the joints in the area of ​​the connection of hoses or pipes.

Aquastop electromagnetic inlet valve built into the filling hose

Sometimes situations arise when a safety valve located in a pouring hose does not open, although there is no leakage in the dishwasher. Such a breakdown is treated only by replacing the intake hose along with the built.in nozzle. To clarify and eliminate other causes of malfunction, it is better to call the master.

The presented video will tell the readers how to replace the inlet hose of the Aquastop system in the Bosch Edition 45 SilenCeplus dishwasher:

The lock or sensor blocking the door does not work

With such a failure on the Bosch, Siemens PMM displays, E06 error code appears. The breakdown can be determined by ear: if the click is not heard when the door is closed, you will have to replace the locking device.

Bosching machine locking castle Bosch

To carry out the repair, act as follows:

  • Deanate the dishwasher;
  • Open the door, unscrew and remove the front facade or panel;
  • Disconnect the cable and unscrew the screws holding the lock lock;
  • Remove the device and replace it with new.

Sometimes it happens that the cause of the defect lies in the ECU, which does not perceive the signal about the closure or does not open the door at all. If the lock is jammed, do not try to open the door yourself, otherwise you can damage the device. Better call a specialist.

Flapsed the inlet valve

Inlet valves. rather fragile devices and do not always withstand pressure above 1 MPa, which can rise as a result. There are other reasons for the refusal, one of which, for example, is the lack of contact with the control unit (chain break). The reason may be the ECU itself.

Intake electromagnetic valve of a dishwasher

One of the reasons for the valve breakdown may be a break in the reel of the control electromagnet. If the power is supplied and there are control signals on the contacts, check if this part is closed inside. If so, remove the valve and clean it from dirt and garbage under a stream of water. If it is clean, then it is to be replaced. This part can be replaced independently.

How to disassemble the PMM and check the intake electrical valve, readers will be told in this video:

Cleaning or replacing the press

A spoiled water level sensor causes an extraordinary situation: water continuously enters the PMM and immediately pumps out the pump into the sewer. Why is this happening? The liquid fills the reservoir, but the control unit does not receive the corresponding signal from the press start and continues to keep the fill valve open.

The case of the press start in the dishwasher, the view from the pallet

This part can also be replaced independently. Its location is shown in the photo above.

We hope that this article will help readers with their own hands eliminate most of the malfunctions associated with the flow of water.

The supply hose is clogged or overwhelmed

The reason that water does not receive, there may be a banal blockage of the hose of the dishwasher. Just as in the previous case, the problem is easily eliminated with your own hands. Prepare a first basin, then unscrew the hose from the bulk filter and drain the water into a pre.prepared container. If there are clogs, disconnect the hose completely and rinse it thoroughly under running water. Next, the hose must be put in place. During the installation, make sure that there are no bends, check the loyalty to the installation of gaskets.

By the way, water may not flow or bad even if the hose is pushed. Therefore, check this moment.

Prevention of a repeated occurrence of a problem

To do this, follow the following simple rules:

  • monitor the hoses, prevent bending, pushing;
  • monitor the filter. conduct preventive cleaning once a month;
  • If there are voltage surges. install the stabilizer;
  • If there is a frequent drop in pressure in the pipeline, install a hydroelectric station;
  • use only special dishwashing products;
  • If the water is hard, carry out preventive cleaning once a month to remove the scale, or constantly use funds from salt;
  • take care of the door, gently closing it, avoiding the hit of foreign objects.

All you need to know about water for a dishwasher will find in this section.

Elimination of blockages

In each of the above cases, in order to restore the performance of the equipment, it is necessary to perform certain manipulations. How to do this, we will tell further.

Filter cleaning and pump checking

In the dishwasher, the filter consists of two elements connected together. This design is located in the bottom of the working chamber. In most models, the main filter is framed by a filter mesh, which is also a filter that does not pass food waste.

Filter and filter mesh are removed outward for cleaning

The internal “glass” is made of large.earned mesh and is a filtering element of rough cleaning. When the water passes through this part, it enters the surface of an external metal mesh with small cells. a filter element of thin cleaning, which finally cleans the liquid from food residues.

Filtering elements of rough and thin cleaning

To clean the filters, perform the following actions:

  • Get baskets for dishes from PMM.
  • Unscrew the filter lid, which is located in the bottom of the camera, next to the sprayer.
  • Pull two dirty filtering “glasses” from the niche.
  • Rinse both filters thoroughly with running water. If necessary, use a toothbrush and any detergent for dishes.
  • Open the lid, which is located under the filters and gives access to the pump impeller. Carefully check whether the impeller rotates freely. If something slows down, you should remove the blockage with tweezers.
  • After cleaning, return all the details to your place.

This is what a porch of the impeller looks like in many PMM and Siemens PMM models

Cleaning the sewage system

In this case, the pump does not have time to remove all the water during its work, since the sewer system is clogged. Localizing the malfunction is simple. disconnect the drainage hose from the sewer.

If dirty liquid flowed from it, try to clean the part on your own, for what:

dishwasher, does, gain, water
  • Pour boiling water into the drainage hole with dissolved pipeline cleaning (perhaps only a siphon has closed).
  • If there is no result, try to clean the pipe with a steel cable (if you have it) or invite plumbing.

Checking a drainage hose

It happens that the cleaning of the filters and the sewage check do not lead to the desired result. the water still does not pump out. This may mean that he has clogged or pushing the drain hose.

First, check if the hose is pushed with furniture or other items. Feel it along the entire length (such a manipulation helps to remove the blockage). After you make sure that the hose is clean and does not overpower, turn on the dishwasher to check the drain system. You can disconnect the drainage pipe from the sewage system and send it to a large container to make sure its performance.

Disconnecting the drainage hose from sewage

dishwasher, does, gain, water

Checking and replacing the pump

If the Bosch dishwasher does not drain water and the sound of a working pump is not heard, you will have to check and, possibly, replace this part. For this:

  • Remove water from the PMM chamber in any convenient way.
  • Remove the drain filter.
  • Put the machine on the side.
  • Remove the pallet and disconnect the Aquastop system sensor from it.
  • Remove the pump and disconnect the nozzles from it.
  • Check the impeller (it should rotate freely). If it jams, replace the pump.
  • Check the resistance on the pump contacts with a multimeter. It should be within 200 Ohms if the pump is working. Otherwise, the pump needs to be replaced.
  • Make sure that voltage from the control unit comes to the pump. If not, perhaps the ECU is faulty.

Extracting the pump for diagnosis and replacement

I would like to note that it is better to entrust the diagnosis and replacement of such faulty details as a pump, press strata and an ECU. They have experience and the necessary devices for verification, and you do not have to look for original spare parts for repair.

Water is not supplied to the dishwasher

The most elementary solution to the problem may be a situation when there is no water in the water supply. However, if everything is in order with water supply, then it is worth studying the options when the inlet valve is broken, or the net is closed in front of the valve. What to do in this case?

If an additional flow filter is installed on your hose, then you should also remove and clean it from pollution.

Only two points are able to eliminate most problems with a set of water, as well as with the refusal of the machine to start work. But if this instruction did not help you, then you should additionally study the bulk valve, for which you must first remove the lower panel of the machine, and then find the valve in front on the left of the device. Disconnect the wires from two valve contacts, take a standard multimeter with an ohmmeter mode and check the element resistance. If the data differs from the norm, then the part is faulty and requires replacement.

Check the circulation pump

When everything is fine with the supply of water, the pump itself is most likely to blame for the circulation of water inside the dishwasher. To conduct diagnosis and repair, you will have to partially disassemble the device.

  • Disconnect the unit from all communications.
  • Put the machine into a spacious room where it will be convenient to disassemble.
  • Put household appliances on the floor.
  • Remove the bottom of the “Homemade Assistant”.
  • Remove and temporarily remove the pallet so that it does not interfere.
  • Also do with an introductory nozzle.
  • Remove the circulation pump by turning off the wires and disinfecting the latches.

For reliability, take photos of the wiring, so that then there is an example of connection before your eyes.

If the element is damaged, then it is much easier to buy a new one and install in the place of the old. However, the repair of this part is not very complicated, so if there is a desire, then you can fix the pump with your own hands and save a little.

Midea MINI dishwasher installation and operation video

Why doesn’t water enter the dishwasher

During use, a dishwasher, like any other household device, fails. There are situations when the dishes were loaded, the powder was covered, the program was installed, but after pressing the start button, the water does not enter the unit. The reasons why the dishwasher does not get water is several. Some of them can be eliminated independently. Complex cases trust qualified masters. Consider possible malfunctions and ways to eliminate them.

The program of the dishwasher (PMM) laid a certain time for which the tank is filled with the necessary water with the volume of water. It depends on the model and is 10-15 minutes. If for the set time from the water level sensor there is no signal to the control unit about the fullness of water, then the PMM stops the execution of the selected program.

In equipment without a display, an indicator of water supply begins to flash: a button with the image of a tap, button “Water” or “End”. On the displays of modern models equipped with a self.diagnosis system, an error code appears.

The code combination of error associated with the supply of water varies depending on the brand of the dishwasher:

  • On the Bosch and Siemens display, the E3 or E8 code appears;
  • on the display of Candy, Hansa, Krona and Samsung. E1;
  • on the Beko display. 0000;
  • on the ariston display. A10;
  • on the LG. IE display;
  • on the indesit display. A102;
  • On the Electrolux and Zanussi display. I10 or IF0.

Advice. If, after the error code appears, the machine tries to continue to work, then it is turned off so that the electric heater does not burn out.

If the liquid is not gained in the dishwasher, first check:

  • The presence of water and pressure in the tap. Open any crane in the house to make sure that the water is not disconnected due to preventive or repair work.
  • Stopcock. When connecting a dishwasher on a tap pipe, a special shut.off valve is installed. To be able to block water. If it is blocked, then it is opened so that the device begins to work.
  • House of household appliances. If it is not closed to click, then the program does not start, since the control module does not receive a signal about the door lock. After close closure, the device will begin to gain liquid.
  • Water supply hose. If it is twisted, extended or rude, then the water does not enter the dishwasher and the protection from the Strait Aquastop is triggered. After eliminating the indicated reason, the machine should be started again.

All of the above reasons why the liquid is not gained in the device are eliminated without much effort. If the water is not disconnected, the hose is not overheated and the door is tightly closed, then a more serious malfunction arose. In this case, the household appliance is disconnected from the network and try to independently identify the cause or cause a qualified specialist.

Diagnostics of the causes and elimination of malfunctions of the dishwasher

To the most common reasons why the dishwasher does not gain water include:

  • not a closed door, as the door lock broke;
  • The filter clogged;
  • The water water system blocked the supply of fluid;
  • The temperature sensor broke or burned out;
  • problems with the control module;
  • Flapsed the filling valve;
  • The water level sensor has broken.

Some of the reasons can be eliminated independently, for example, to clean filters. complex breakdowns require certain knowledge and the availability of special tools.

Advice. If the dishwasher is under warranty service, immediately contact professionals.

The door is not closed

A castle is installed in the device door, which protects it from leaks. When it is closed, a signal about the door blocking is received on the control module, the machine begins to work. If the lock is broken, then the door does not close to a characteristic click. The blocking signal does not arrive, the program does not start and the liquid is not gained.

In case of locking of the lock, it can be changed independently. How to do it:

  • The dishwasher is turned off from the mains;
  • unscrew the front panel;
  • Unscrew the broken door lock;
  • install a new latch;
  • Flow the panel.

Filter blockage

The inlet valve filter is installed to protect the equipment from dirt and garbage, which fall from the water supply. It is periodically cleaned or changed. If the liquid is too slowly gained in the dishwasher or does not enter at all, then the reason is most often in the clogged filter. It is cleaned on their own or caused by masters.

Before cleaning, the water supply is blocked. Unscrew the hose, remove the filter. It is located at the inlet in the inlet valve. The net is washed under a stream of water. With severe pollution, it is cleaned with a needle or lowered into a solution of citric acid (30 g per 1 l) per hour. Then the cleaned filter is installed again, the hose is attached.

The water area worked

Dishwashers are equipped with a protective system from leakage. aquastop. The reasons why the technique ceases to work:

If a leak occurred and the liquid hit the pallet, then it will be eliminated. For this:

In case of failure of the system itself, it is repaired by professional masters. Electromagnetic valves often burn out. Their integrity is checked using a multimeter. If it shows endless resistance, then the valve burned down. Replacement is made in a repair workshop.

The temperature sensor or heating sensor is faulty

With a faulty temperature sensor (thermostat) or Ten, the water begins to gain, but then washing stops. This is because the liquid does not heat up to the temperature set by the program. Diagnosis and replacement of the thermostat in the dishwasher, as well as the replacement of the burned heating, are performed by qualified specialists.

Problems with the control module

The device control module is under the front panel, in the door. He distributes commands to systems, controls compliance with sink modes. In case of malfunction of the module, the technique stops working or works with failures.

To check the integrity of the plateau, the door is disassembled. Visually determine the presence of defects. The faulty module is reflamped or qualified specialists are changed.

Falf valve

After starting the operation of the dishwasher, the control module sends a signal to the pitch valve. It opens and the liquid is filled. If the pump is buzzing, but does not download, then the valve is closed or damaged. The blockage is cleaned themselves or invite a specialist.

The damaged valve is changed, since it cannot be repaired. In addition to damage to the valve, a circuit is possible from the control unit. Diagnostics and replacement is made by the master.

Water sensor malfunction

A faulty water level sensor (Pressostat) submits distorted information about the fluid level to the control unit or does not give signals at all. If the signal is given that the reservoir is complete, although this is not so, then the water will no longer flow. In the absence of signals, it also does not act. In this case, the press is changed.

It can be replaced independently:

  • equipment is disconnected from the mains;
  • turn over and remove the pallet;
  • visually determine the presence of defects on the sensor;
  • Check with a multimeter: the lack of voltage indicates a malfunction of the press,;
  • The broken sensor is changed to a new.

Main reasons

As a rule, those nodes and parts of PMM that are subject to mechanical influences in the process of functioning are broken, have a complex device or contact with low.quality water. The causes of breakdowns are associated with the mentioned aspects.

Filter filter

Water from the water supply network to rarely where there is completely clean. Various impurities, sand, rye and other garbage are constantly served in our home in parallel with water. These pollutions can disable a dishwasher, in this regard, all manufacturers provide in advance to protect their products from pollution. It is executed in the form of a bulk filter.

His mesh stops all the garbage on itself, nevertheless, after some time, it is able to clog and block the flow completely. Often a rumble is heard, but the car does not start. In the PM, the filter is on the water supply hose, in the area of ​​connection to the body.

Therefore, it is necessary to unscrew it, initially the flow of water on the riser pipe.

The fill hose is clogged or transmitted

The reason that water is not gained is the usual blockage of the hose of the dishwasher. Similarly to the previous case, the problem is easily eliminated on its own. I must say that water may not flow or bad even when the hose is transmitted. Therefore, control this moment.

Lack of water in the water supply system

Problems are happening not only due to the failure of the dishwasher, but also due to interruptions in water supply. The flow of water can be absent both in the system of continuous water supply, and in the supply hose. The blocked faucet will not like to use the dishwasher in the same way.

Aquastop failure

Depressurization between the elements of the dishwasher leads to the occurrence of water in the pallet. There is a system of protection against leaks. “Aquastop”. If it works and syntilizes, then the control unit using automation will interrupt the filling of water. At times, false triggering happens when the sensor itself becomes inoperative.

Doors problems

The door of the dishwasher has a complex structure, and violations in its work are not uncommon. As a result, there are usually several factors of an inoperative state:

  • violation of the fixing mechanism, when the door is not able to close to the end, as a result of which the sensor does not work, and the device does not start;
  • the way out of the door lock;
  • The lock closing sensor does not turn on.

Damage to the sensor (sensor) water level

The amount of water entering the dishwasher is observed by a specialized device. Pressostat. Actually, through it, the control unit transfers commands to the beginning and completion of the water set. Когда он функционирует неправильно, появляется вероятность перелива бака и срабатывания AquaStop, или подача воды совсем не стартует.

The cause of the problem may be damage that arose from the action of mechanical factors, or clogging the sensor that determines the water level.

Посудомоечная машина Midea ошибка Е3

Office of the control unit

The control module is a composite electronic device that includes several relay and many radio elements. If at least one part loses working capacity, then PMM may either not start at all, or start functioning incorrectly, not excluding the refusal of water recruitment.

Due to the complexity of this node, it is better to entrust diagnostic works to a professional. To correctly establish the cause of the failure, not only specialized devices will be needed, but also the practical experience of such work.

Trouble-shooting

Most of the malfunctions can be eliminated on their own. Diagnostic work should be performed to determine the cause of the failure. After that, it is necessary to do certain actions to correct the problem.

If you yourself are not able to repair the dishwasher or doubt your abilities, you must contact a specialist. Otherwise, the situation may deteriorate.

If the filter is clogged

Water in a centralized water supply has a certain level of purity and softness. As a result, the filter is often clogged. This leads to a lack of water set, or it can get extremely slowly.

A specialized mesh-filter makes it possible to protect the car from such problems, protecting from impurities and abrasive particles.

To fix such a problem, you need:

  • block water and unscrew the water supply hose;
  • Find a mesh-filter-it is located at the place of interfacing the hose and dishwasher;
  • Peel it by means of a needle, in addition you can apply a solution of citric acid. the element is placed in a solution for at least 60 minutes.

Inoperative the filling valve

The water set stops when the water bay valve fails. He stops open after receiving a signal on him. The valve may fail due to constant jumps of water pressure or voltage. The device is a non.combination. He needs a replacement so that the machine has the opportunity to pick up water again. It is advisable to contact professionals to take an event. It may not be possible to change the element with your own hand.

Damage to the press starter (water level sensor)

Pressostat is required to measure fluid levels. As soon as he fails, he begins to give out incorrect parameters. The dishwasher carries out more water than required. This leads to transfusion.

And when the submission indicator flashes, but the water is not supplied, therefore, the press.start of the press failed. It is necessary to change the press system:

  • Disconnect the device from the mains and overturn it on the side;
  • If there is a cover on the bottom of the lid, it must be removed;
  • The water level sensor looks like a plastic box. it is necessary to remove the tube from it with pliers;
  • Turn out a few screws and dismantle the press, examine the presence of garbage;
  • Through the multimeter, measure the resistance on the contacts. this will make it possible to verify the performance of the element;
  • Install the new sensor.

Problems with the control module

The control unit controls numerous processes in the typewriter, including sending signals about turning on and off. When it has problems, the dishwasher begins to function incorrectly. The block cannot be repaired on its own. You need to contact the service to professionals. You can only make sure the device breakdown. To do this, the camera door opens and the bolts turn out.

After finding the board, it is necessary to inspect its appearance. If there are burnt.out wires, therefore, the problem is in the block.

When the Aquastop system is triggered

It is impossible to fix Aquastop, it can only be changed.

There are 3 varieties:

  • mechanical. the work of the gateways is configured by a spring, which functions taking into account the pressure of water;
  • adsorbent. when fluid enters, specialized material becomes larger in volume and stops the supply of water;
  • electromechanical. float, when lifting the fluid level, the float pops up, and the flow of water stops.

Determine the type of device. For this they watch the leadership, passport.

  • mechanical. put the spring in the initial position, turning the locks;
  • adsorbent. wait until it drys;
  • electromechanical. dismantle and change.
  • turn off the PMM from the mains;
  • Close water;
  • turn off the old hose, disconnect the plug;
  • acquire a new one;
  • mount in the reverse order;
  • Run the car.

The door lock is faulty

A shut.off mechanism is installed in the door of the dishwasher of the dishwasher. Electronic locking of the lock does not allow leaks.

If water does not enter the car, there may be a castle malfunction. With such a malfunction, the pump will not pump water into the camera, such a mechanism is provided to avoid leaks.

When eliminating the malfunction, it is necessary to perform the following actions independently:

  • The device must be de.energized. This is done as follows. a fork is removed from the plug.
  • Open the door of the device and unscrew the screws fixing the door panel.
  • After removing the panel, unscrew the screws of the lock lock device.
  • Replace the faulty with a working lock.
  • After replacing, make an assembly in the reverse order.

The inlet valve broke

In the technique of the intake valve, it performs an important function for monitoring and supplying water to the chamber. When the technique is turned on, the processor gives a signal, and the inlet valve begins to fill the camera with liquid. If water does not supply the dishwasher in the dishwasher, the reason may be in a fault valve malfunction. The valve can only be examined after dismantling.

First of all, it is necessary to turn off the equipment from electric power. Then remove the pouring hose and a net and be sure to rinse the filter.

Secondly, open the cover of the apparatus, disconnect from the part of the wire, disconnect the fixators.

Lastly, turn the valve and remove it from the body. If the electronics is in good way, there is a chance that the valve is clogged. In this situation, you just have to disassemble the detail and clean. If all the same is faulty. it is better to install a new valve, make the assembly in the reverse sequence.