Samsung Inverter Refrigerator All PCB Led Blinking Error Codes (1/2/3/5/6/9/11/13 Time)

samsung, refrigerator, blinks, temperature, freezer

Samsung refrigerator flashes the upper chamber temperature indicator

In the No Frost system with dry freezing, a fan is used inside the refrigerator. Its use leads to the fact that the flows of cold air inside are constantly mixed by more uniform cooling of products. After warming up, the air takes the resulting condensate, bringing it out.

This method of work is possible due to the fact that the Samsung refrigerator is a two.chamber No Frost has high reliability. However, over time, the technique wears out and the likelihood of malfunctions increases. In such a situation, it is important to correctly determine the cause of the problem. Of course, having called a specialist, it is easy to do this.

Important! Samsung has created a built.in electronic diagnostic system in its refrigerators, which allows even an inexperienced user to determine what happened to the technique.

However, in order to do this, you need to know how to use such a diagnosis. Based on the data obtained from the sensors, it draws conclusions about the nature of the malfunction. After performing the analysis of the information received by her, she determines the type of malfunction and issues on the display located on the panel, the error code.

Knowing how to read it correctly, the user can easily find out the type of Samsung No Frost that has arisen in the refrigerator. There are instructions that describe in detail what needs to be done in each situation, depending on the code issued by the system. At the same time, it is immediately clear when it is possible to take independent actions, and in what cases you need to call the master. With the list of faults of the two.chamber refrigerator Samsung No Frost, you can find in the corresponding table.

Ways to eliminate breakdowns in Samsung refrigerators

RSA1SHVB1 two-chamber refrigerator (Side by Side) with electronic control and No Frost in both chambers (1 motor-compressor). The freezer stopped freezing, on the display the temperature 21, the freezer and the refrigerator 16 and the display blinks. If the freezer does not work, then the reason may be a malfunction of the evaporator tightening system (the tickle sensor or the heater of the evaporator). If both cameras do not work, then the reason may be in the leakage of the freon, a compressor malfunction or control module. Tell me, the refrigerator Samsung RSH5ZLMR1 (two.door) Side Bai Side is squeaking melody as if the door is open. And the temperature itself changes. If you have x-k RSH5ZLMR1 issues sound signals, with a door closed, then this indicates a malfunction and insufficient temperature in the chambers. There may be a malfunction in the control module, a freon leak or in the failure of the temperature sensor. Refrigerator No Frost Samsung RT 25 HAR4DWW. Water often leaks from the grate under the freezer. I received an answer that you need to remove the casing and clean the drainage tube. The casing took off in x.to. And in the freezer, I did not find a phone, although I was looking with a flashlight. There is a flimsy pallet, it did not dare to remove it. There is no ice on the evaporator or under it. Indicate where this tube is? Or can pour hot water on a tray? And yet, if the temperature controller is rotated to the right, then we lower the temperature? After disassembling the minus temperature at the minimum of the regulator. The drainage tube is under the evaporator below. The pallet that you were afraid to remove is served in order to condensate the text in the drainage. Two.chamber refrigerator Samsung RSA1StWP1 Side by Side with electronic control and inverter compressor. Tell me what the buttons block are called correctly, which are pressed when closing the door so that the light does not burn? The sensor that is responsible for turning off the light and indication with a long-open door of the x-ka RSA1STWP1 is called the Herkonian door sensor. Two.chamber refrigerator Samsung RT 25 No Frost. When included in the network, only the light bulb is included in x.to., nothing else. The noise of the compressor is not heard. I wanted to pull out a launcher, but it did not work. How to remove it? Tell me, please, where can be the cause of the breakdown? The launch vehicle of the relay is extremely rarely out of order. It is removed simply: unscrew the screw on the lid, and the lid will be removed. If both cameras do not work, then there may be the following breakdowns: the failure of the motor-compressor; Freon leak in the system; A breakdown of the tie timer (the unit got into a touch and does not work); The failure of the thermostat; Failure of the heater of the evaporator. RSH5ZLMR Side by Side two-chamber refrigerator with Full No Frost, electronic control and one compressor engine. There were interruptions in electricity for several days, after that mor. The camera began to freeze the meat poorly, and setting the temperature on the scoreboard.17 degrees, could not be rearranged on these numbers, and it comes out.25 and could not fix it. Hol. The camera works as usual. What to do in this case? The reasons that the freezer is rewriting, there may be a lot. To begin with, we recommend defrosting x-k RSH5ZLMR and, if the freezer continues to grounder, then the case can be in the control module and in the temperature sensor of the freezer and pr. Samsung RSA1SHVB1 two.door, Side by Side, inverter compressor. The freezer, instead of the minus, works in a plus, heats up to 30 degrees, which could be? You have x-k RSA1SHVB1 with No Frost, then the case may be in the leak of Freon from the system. If the unit is two.compressed, then the thermostat mor can be faulty. cameras (temperature sensor) or freezer engineer. Samsung RSH5ZLMR Side by Side (two.door). In the refrigerator compartment, the air stopped circulating, and ice was formed in the area of ​​the ventilation hole. A few days later, in the freezer, which previously worked, the temperature rose stably to plus 3 degrees. Yesterday I took off the grate from below on the rear panel of x-ka, washed it along with the sponge mounted on it, and sprinkled carefully. From x-ka previously extracted all the contents. After turning on the empty unit, the temperature in the freezer compartment gradually decreased to 14 degrees, and in the refrigerator compartment remained room temperature. Further temperature decrease does not occur. Initially, apparently, you had a malfunction in the system of hidden the evaporator No Frost (the sensor of the hits, a fuse or a heating heater). Now, most likely, Freon’s leak. Diagnosis of the master is needed. I have a two.chamber refrigerator Samsung RT 25 HAR4DWW. I wanted to ask how to install a dispenser. When the refrigerator itself was installed, they asked about the installation of the dispenser. Refused, now I think how to connect? How to install a dispenser you will find in the operating instructions. Two.door refrigerator Samsung RSA1STWP1. The fan does not work. precisely, the power of 220 volts does not come, but only 60. Most likely, problems with the electronic module or the fan itself. The two.door double.chamber refrigerator Samsung RSH5ZLMR1 Side by Side with the No Frost system in both chambers and one compressor. It works, then the temperature display does not work. Can show one temperature, in fact in the upper and in the. the camera is the process of defrosting. Sometimes squeaks. What to do? It is necessary to check the controls of the control module and the temperature sensor of the refrigerator and freezer chambers. Please tell me what is the inner diameter of the capillary tube in Samsung refrigerators? The fact is that the diameter of the tube does not depend on the brand, but depends only on the power of the refrigerated production and the brand of Freon. The refrigerator Samsung No Frost is constantly squealing, while the Vacation and Super Freeze buttons are burning, please tell me, please? Vacation means the on vacation mode. To turn it off, you can hold the Vacation button for 10-15 seconds, or with the help of increasing and reducing temperature, raise by 1 degree or lower the temperature in one of the chambers. Super freeze means super.commercial. Samsung, the S28BKCSWN/BUS model with a GQR70AG compressor, works without problems, but turns off with a roar, as if something jammed inside the compressor. Please tell me what to do or call the master? It is necessary to put forward the unit and see if the compressor hurts for one of the tubes behind him. Also, pay attention to the rubber shock absorbers (gaskets) of the compressor installation platform, maybe they are dry. Samsung RF62UBR S SIDE by Side. After turning off the electricity, the Hill stopped working. The camera appeared water. Freezer freezes well, incomprehensible symbols on the display. If x does not work.To., then you need to check the freezer chamber. If there is a lot of snow and ice in the freezer, then the matter is the breakdown of the evaporator’s hidden system (the sensor of the tackle or the heater of the evaporator) and the snow prevents the fan rotation. If there is no snow, but the fan does not rotate, then the matter is either in the fan motor or in the temperature sensor X.To. I have samsung no frost. On the front panel, the temperature indicator x.To. constantly flashes and the temperature inside is very high.18 degrees. The instructions say that when the temperature indicator blinking, you need to call the service center. We live in rural areas. What should we do? If in x.To. too low temperature (-18 degrees), the cause of the malfunction can be in the failure of the temperature sensor. If the high temperature (18), then the case may be in the failure of the system of the hollow of the freezer of the freezer (the latch sensor, the heater of the evaporator). Samsung refrigerator, model S28BKCSWHN/BUS. Holo does not work. camera, and the freezer works. Check the freezer, if there is a lot of ice and snow in it, then it interferes with the rotation of the evaporator fan, which leads to the fact that cold air does not fall into x.To. In this case, it may be in the system of hiding the evaporator. a tiemer of the thaw or heater of the evaporator. If there is no snow and ice, then check if the fan rotates, maybe the fan motor is out of order. There is a two-chamber with the No Frost system, it was bought for a long time, the model is not known at the moment: the freezer is working properly, the lower “cabinet” seems to be unreasonable, according to the sensation, the temperature is high, the products sometimes spoil prematurely (the adjustor handle is maximum). What could be the problem? There are many problems in models with the No Frost system: the heater burned out, the thawing sensor has burned out, the fuse (special) was out of order, and also in some models there may be a freon leak, etc.D. Samsung RL28DBSW, the upper chamber does not cold at all. The problem in the freezer. It is necessary to diagnose the thawing system, grounding air ducts, temperature sensors. For a complete and accurate diagnosis, you need to call the master. The electronics of the RSE8KPAS model is buggy. Detachment description: spontaneously switches from normal mode to Vacation and backward mode. A simple attempt to turn off the power and turn on again did not help. At the entrance to the Vacation mode, the Vacation button itself ceases to obey. When unauthorized to return to the Cool mode, does not want to listen to the Freeze button. What will you advise? Judging by the description, this is a malfunction of the control board, possibly a connecting train of the door console with a control board. It is necessary to call the master. The compressor does not turn off in my refrigerator, which could happen? There may be several reasons. Insufficient amount of refrigerant in the system due to leakage, and this is not gaining the necessary temperature in the refrigerator. The thermostat malfunction (temperature sensor) refrigerator. The door is not closed. The unit needs to be turned off and called the wizards for diagnosis three days ago bought x-k RL46RSBSW. Alarm is the fact that the side walls of the case are heated during the compressor work somewhere up to 40-42 degrees. Please tell me, this is a normal phenomenon or it is necessary to intervent a specialist? This phenomenon for these models is quite normal, condenser blocks are located on the sides of the refrigerator, which heat up during operation. Model RT 44MBPG. It all started like this: it began to drip water in the hill. Department. Stopped automatically launched (turned on forcibly, off./ON. In the outlet). Stopped freezing in the freezer. He stopped cooling at all. The compressor works, the fan is noisy, but there is no sense. Please tell me a possible breakdown. Most likely there was a leak of refrigerant, and therefore it does not cold. A call call is required. When transporting the Samsung RT37MW refrigerator and installations, a puddle of water began to form when it is hot. Tell me how to fix it yourself? In order not to form a puddle of water, you need to tilt x-ka back with two front wheels that are below, or a drain pipe jumped during transportation. We purchased the Samsung refrigerator with the No Frost system less than a month ago. There were no problems for two weeks. But yesterday, as I understand it, the cold in the refrigerator stopped produced. The freezer works without problems. In the store they advised to turn it off for a couple of hours, and then turn it on again. So they did, but today everything seems to be fine again, after thawing, but this situation still bothers me. Really only hot weather (as explained in the store) the reason for such a failure? Climate conditions do not affect the operation of refrigeration equipment. Perhaps there is a factory marriage, in this case, contact the warranty service center. X-K RL28FBSI1/XEK. After the electricity interruption, the compressor stopped turning on automatically, but when the super frost is turned on, the compressor works. In this situation, most likely, the control board or temperature sensor was out of order. A calling the master is required. In the right corner of the Holler. the cells over the vegetable basket intensify the ice. Have to defrost every week. Leakage on the evaporator. To save the unit, you need to change the evaporator. The main malfunctions. as a rule, this technique is equipped with a control system based on an electronic controller, in this regard, the control module malfunctions occur quite often in comparison with the rest of the brands. Any household appliances have its weaknesses. As experience shows, the need for repair in most cases is associated with such malfunctions. The failure of the electronic control unit. Replacement of the temperature sensor (thermoresistors). Problems of the thaw system. Malfunctions in the No Frost system. It is not rare that there are cases when the tube is clogged to drain water from the evaporator of the chamber, as a result of which a puddle of water is formed around the unit.

Why is the freezer temperature indicator

If the Bosch refrigerator gives a sound signal, then the temperature mode in the chamber is broken. This happens for various reasons. The first group of problems does not cause serious concerns and after several manipulations the device will work normally. Such problems are the following:

  • The device is new and, with primary inclusion, has not yet gained the necessary temperature;
  • The refrigerator was disconnected for a long time;
  • A lot of fresh products are loaded into the device, the temperature of the medium increased; on the door from long operation became unusable.

The first three points will disappear by themselves after eliminating the cause. As soon as the temperature drops to the required mark, the button will stop flashing. In the latter case, you will have to change the seal.

serious problems include those when some detail is damaged. The most common are breakdown:

If the problem has not been able to independently solve the problem, and the indicator burns for more than two hours, you need to contact the refrigerator repair service, where they will make diagnostics and identify the cause.

Why is Bosch squeaks with a door closed

The latest models of refrigerators along with cooling and frost functions have a protection system, which will avoid damage to the unit.

Когда же аппарат при закрытой двери просто пищит время от времени – это явный признак того, что в агрегате неполадки. The sound signal for no apparent reason tells the owner that some details inside are working incorrectly. This is an occasion to urgently contact the master who will make diagnostics and eliminate the cause.

Why do not freeze refrigerators with the No Frost system

The fact is that this system in modern refrigerators is not perfect and not protected from breakdowns and malfunctions. These are refrigerators of various brands: Samsung, Bosch, Indesit, Becco, etc. Such refrigerators work on the principle of dry freezing. Therefore, the cause of the breakdown may be the heaps that failed. To check such a version, the refrigerator needs to be thawed and observe how the hets themselves work.

In addition, if the refrigerator is two.chamber, you need to find out exactly where the problem is available. It may also be that the upper chamber of the refrigerator No Frost is badly freezed, and the freezer works fine. Or vice versa.

Another reason for the malfunction may be a compressor breakdown.

In the refrigerator with the No Frost system there is an evaporator, which is located between the walls. There is a cooler (fan) in the back wall, which provides air movement in the chambers. After some time, a slight defrosting occurs due to the fact that the heating element heats the air in the walls and chambers. Subsequently, moisture accumulates in a special container, later it is evaporated.

Sometimes the cause of the breakdown is a non.working fan. This can be determined by the following signs:

This can happen due to freezing of the fan itself. To fix it just just defrost the refrigerator.

The refrigerator freezes a lot

The upper chamber of the refrigerator is badly freezed

If the refrigerator has become very freezed, at the first moment you need to check whether the regulators are exhibited correctly. What to do if the camera freezes, the compressor works, despite the switching of the regulator lamb to the zero position? Stop the refrigerator, change the thermostat yourself or call the master. In the refrigerator with electronic control, an air sensor is used. The specialist should change it.

It happens that the refrigerator is too much freezing, and in the freezer tacus meat. What to do if the compressor works without stopping? Presumably, there was a blockage of a capillary tube due to the decomposition of oil and refrigerant. Eliminate the blockage or replace the capillary specialist.

The refrigerator began to freeze very much. the food freezes

A genuine disaster for users will become if the refrigerator is very frost. What to do if the cavity inside freezes with a fur coat, products relate to ice, lose their taste, freeze. First of all, you need to find the cause of the disaster.

  • check the settings of the parameters and modes of the refrigerator;
  • make sure the density of the door closing; drain hole if it is clogged with ice;
  • make sure that the thermostat is working, reacts to commands.

Check how electronic control works, reconfigure and debug the mode only a master. In the meantime, you need to move the products from the walls, shift to the warmest part, closer to the door.

The refrigerator is badly freezed and does not turn off

If the refrigerator does not turn off and freezes very much, there are several reasons:

samsung, refrigerator, blinks, temperature, freezer
  • There is no command to turn off due to a malfunction of the sensors or relay of thermostat;
  • The “Super.Summary” mode is selected;
  • management failure;
  • loss of compression in the unit;
  • malfunction in any of the elements of the heating circuit.

Modern electronic control refrigerators are complex. The best you can do is to free the cameras from the products and call a specialist. Before this, you need to check, signs of malfunctions set forth in the instructions.

The refrigerator No Frost is badly freezing

No frost is considered a complex system for the transfer of cold from the evaporator to the chamber. The evaporator radiator is located behind the wall, there is a fan, which forcibly blows the air from the chamber through the gaps between the cold tubes, taking the cold. Cold air enters the chamber, and heated, with moisture, approaches the evaporator, leaving hoar on the tubes. When the compressor stops, the heater periodically turns on, the steep water is removed into the drainage.

Why does the refrigerator with No Frost begin to freeze strongly? Evaporator and the entire air cooling system are in the freezer compartment. The cold chamber gets cold on the air duct with a damper. If the evaporator tube system does not work, it is overgrown with ice, heat transfer decreases.

There is not enough cold in the upper chamber, the compressor will work, cold air enters constantly. At this time, the freezer is badly freezed in the refrigerator. Why? The compressor works for a long time. Later the fan will stop, its blades are icing or it will jam it. The temperature will begin to rise in both chambers.

In the upper chamber, the temperature at no frost may drop if the drainage hole is clogged and the water does not leave. The refrigerator will freeze too much. Drops will begin to condense on the walls from the air and freeze, blown up by cold air. The temperature in the plus chamber will decrease to 0 0 C and below.

Why the refrigerator began to freeze hard

The heat selection system in the refrigerator with one compressor is dynamic. This means that a decrease in temperature in both chambers is possible for a short period. After all, the compressor did not become more powerful, the refrigerant was not added. The influx of cold is provided due to the continuous operation of the compressor. This is exactly what happens if thermoregulators in the chambers are simultaneously placed in super.commercial and rapid cooling. The refrigerator is very frozen, but not for long. If you forgot to turn off the intensive mode. everything will freeze.

The electronic control node failed, the air sensor failed the refrigerator can be very freezed, or it may heat up. Why should a specialist be called for diagnostics. everything is not obvious. The more complicated the technique, the more breakdowns options with similar signs.

It happens that the freezer is badly freezed in the refrigerator. It is necessary to check if the mode for fast freezing is switched. Another reason may be the redistribution of the refrigerant through the magnetic damper into one of the chambers. In a faulty state, it will cause why the refrigerator is very freezing, and heat in the freezer.

If the refrigerator has begun to freeze very much, without tightening, you need to contact the service. Increased load on the nodes will lead to an accident. Instead of refueling, freon will have to change the compressor.

Why does the Samsung refrigerator do not function

When the technique with the No Frost system does not work, there may be many reasons. The thawing system directly is represented by several nodes and details and a full diagnosis is performed to accurately determine the place of malfunction. Potentially, when the Samsung unit does not work, the following components could fail:

When the motor-compressor is faulty, it does not start, clicks are heard. With breakdowns of a launched relay, when it deteriorated or stuck in one position, when the wires going to it are crushed, the compressor is launched. In this option, a damaged part is replaced. When the air sensor came out of the system, he does not transfer commands to the temperature control module in the chamber.

If the heater of the evaporator broke, then thawing the refrigerator does not occur, and a snowy “fur coat” grows on the walls of the compartment of the compartment. In this situation, a faulty part is replaced. This problem is characteristic of the Samsung refrigeration equipment RL40EGPS model. When the pipeline is damaged, the gas.shaped refrigerant comes out and the refrigerator stops freezing. For repairs, they call a specialist who discovers the place of breakdown, eliminates it and fills the system with a “fresh” freon.

Reference! Determine why the upper chamber does not freely freeze or the Samsung refrigerator does not work, only the master is capable of after a full diagnosis. Partially, the problem can be determined by the error code that the unit on the display displays as part of the self.diagnosis program, but it will not be possible to repair the technique based only on this information.

Prevention of breakdowns in samsung units

The manufacturer is attached to each unit, the operating manual is attached, which contains all the necessary information to maintain the operability of refrigeration equipment for as long as possible. The main rules that are necessarily respected by the owner of the Samsung refrigerator if you wish to extend its “life”:

    manually units with the No Frost system is undesirable, since there is enough car defective for washing and cleaning the refrigeration compartments that occurs once in 12 months.

  • When it is necessary to clean the refrigerator in the included state, it is advisable to do this at moderate (16 20 C) temperature in the room. When this rule is neglected, an overheated compressor fails due to excessive load.
  • When washing the inner surfaces of the refrigerator, use abrasive products and aggressive chemistry is prohibited.
  • The back wall is also required to clean from dust and other contaminants, as they can eat into the nodes and elements of the device, which will lead to accelerated wear of parts. Food products are necessary in hermetically closed containers, since due to the features of the No Frost system, food is dehydrated when it lies in an undisguised form.
  • It is forbidden to arrange refrigeration equipment outside the rooms, since household appliances are not designed for the effects of atmospheric phenomena (rain, snow, minus temperatures or summer heat).
  • The unit is located far from contact with direct sunlight and at the distance from heating devices, heating systems, heat surfaces, oven and other heat sources.
samsung, refrigerator, blinks, temperature, freezer

Samsung two.chamber units with the No Frost thawing system are extremely popular models among consumers. These refrigerators are sufficiently reliable, and their cost is not too high for the average buyer. Samsung models work virtually silently, they are economical and have an impressive set of additional functions. Subject to operating rules, such refrigerators can function without failures for many years.

How to rectify the situation

When the temperature indicator flashes on the Bosch refrigerator, you need to press and hold the “M” button for a few seconds on the control panel. At this moment, the most “warm” value to which the camera was heated will arise on the digital scoreboard. Then the figure will change again, demonstrating current indications. Zummer and flashing will be disconnected. All Bosch refrigerators with electronic adjustment are equipped with a similar system. In some devices, for example, Bosch KGP 36360, the role of “Memory” is played by a button with the icon of crossed out the dynamics.

When the red bulb burns on the ATLANT unit burns, you should check the density of the door adjustment to the body when closing: cold air leaks through the gaps can provoke “warming”.

If no air leaks are detected, the work program is exhibited correctly, the light or load of a large number of products in recently did not occur and the device does not need defrost, there is an internal breakdown and a specialist should be caused.

Sensor sensors

The user can independently adjust the temperature from the control panel. the information is provided for it inside the device sensors. It is they who monitor the territory they allocated in the unit. The sensors have the following parts of the device:

  • General refrigerator;
  • internal space in the evaporator;
  • freezer chamber;
  • control panel (for environmental measurement).

Installation of the required temperature regime is carried out using the keoling power or fridge keys (or a mechanical rotating handle). On the control and visible user the panel, data from sensors are received through the control scheme. In most cases, the models from this brand are 502at controllers, which are universal.

The failure of any of the sensors of the device leads to a malfunction of the entire Samsung refrigerator. Such repairs are best entrusted with appropriate specialists.

Ice

One of the frequent problems is an increase in ice. This happens constantly. In most cases, to fight him, it is enough to periodically defrost the refrigerator. After that, you can use the standard way to configure the temperature in the Samsung refrigerator.

In this case, the device is turned off, the products are moved for a short time in a cool place, cleaning the refrigerator and the freezer. The temperature in the refrigerator Samsung rises. Under the influence of room temperature, ice melts. After that, the inner part is wiped dry, loads back products, and turn on the refrigerator Samsung.

However, with a faulty refrigerator, the formation of ice occurs too quickly. If this happens, you need to find the cause and eliminate it.

In this case, the following actions can become the source of the Samsung refrigerator:

  • If hot dishes are put in the refrigerator. Of course, in this way they will cool faster than at room temperature, but at the same time they will greatly violate the thermal regime.
  • One of the common causes is damage or wear of the door sealing. It is necessary to regularly monitor its condition. If necessary, it is necessary to put a new seal.
  • Maintaining the selected temperature regime is impossible without the proper operation of the heat sensor. If it gives incorrect information, then the temperature adjustment will occur incorrectly. One of the possible consequences is a strong decrease in temperature, which will lead to grounding products and the formation of ice.
  • The electronic control of the refrigerator is faulty. For repair, it is necessary to call the master.
  • The leakage of the refrigerant is dangerous. Its deficiency violates the normal operation of the equipment. With its lower amount, cooling to Stan is less effective, which can lead to prolonged continuous operation of the compressor and icing the inner walls of the refrigerator.

Freon leakage and refueling can be eliminated only by specialists. Before you configure the refrigerator, you need to find and eliminate the malfunction.

Samsung refrigerator

Characteristic types of malfunctions

The failure of one of the nodes leads to a specific external manifestation that the user of the equipment sees. Any part of the refrigerator can break, but each manufacturer has different malfunctions.

The refrigerator does not turn on

If one or all the refrigerator cameras are warm, but the compressor does not include the inclusion of the compressor, then there are four main causes of this breakdown:

  • Когда отсутствует любое проявление работы мотора-компрессора и не горят датчики, то это означает проблему с электрикой. First of all, you need to check the power of the outlet and the integrity of the cable. Then you need to call an electrician or call the wiring yourself.
  • The same symptoms can be observed when the refrigerator electronics fail. Although the Samsung technique has a very high quality board and there is high.quality protection against the voltage difference, with poor power supply, their breakdown is still possible.
  • If the indication, control and internal lighting work, but the power of the unit does not occur, then the most likely reason is the compressor malfunction.
  • Similarly manifests itself as a breakdown of the temperature sensor. In this case, the control unit does not receive a signal about the excess of the permissible temperature and it does not give the command to start the compressor.

For Samsung refrigerators, there is a way to determine the performance of the temperature sensor, if cooling does not turn on for a long time, you need to activate the forced cooling mode or accelerated freezing. If the compressor is included in the work, then the problem is in the sensor.

Connecting a temperature sensor to the system using a double.pin terminal is no more difficult than connecting charging to a mobile phone. The main thing is to remember the position of the sensor itself

High temperature in departments

If the temperature in the chambers is high, but the compressor operates in normal mode, then most likely the problem is as follows:

  • Depressurization of capillary tubes and freon leakage. Reducing pressure in the system and air hit the conditions of the phase transition of the refrigerant. In this case, the evaporator’s cold production is reduced or it ceases to function.
  • Loss of tightness of the door, resulting in an uncontrolled flow of warm air from the kitchen room.

The problem with tightness can also be detected by the formation of a small layer of hoarfrost (for the freezer) or condensate (for the refrigerator compartment) in the place where the sealing gum should be adherent to the refrigerator body.

The appearance of condensate does not always signal the breakdown of equipment. Often this is the result of the room in the chamber of hot dishes, uncovered vessels with a liquid left for a long open door

The problem of the formation of ice

As a result of depressurization of the doors, another problem arises. slowly arriving warm air cools near the door and condensation occurs.

In the freezer, where the temperature is much lower than zero degrees, there is an increase in dense snow formations with an admixture of ice particles. In the refrigerator compartment, the condensate seeps through the seal or goes out when opening the door. In this case, on the front side of the refrigerator will be visible incuts.

Even minor damage to the seal leads to the rapid formation of snow growths in the freezer. Therefore, the gum will have to be straightened or changed

Clogging of the drainage system

The condensate formed on the rear wall of the refrigerator is excreted through a special drainage hole. Its diameter is small, since otherwise the cold leak. Water goes by gravity, so impurities gradually settle inside the hole.

The formed narrowing is gradually transformed into a cork that prevents water drainage. A puddle is formed at the bottom of the refrigerator, as a result of which there is an increase in humidity, the spread of odors and the creation of a favorable environment for the propagation of microorganisms. Thus, the conditions of storage of products are worsening.

When clogging the drainage canal, the water without drain returns back to the refrigerator, where it partially evaporates, partially settles besieged on the walls and products

Repair at home

Some refrigerator malfunctions can be identified and eliminated independently. Modern devices have high.quality self.diagnosis, which allows you to identify the problem without involving a specialist. However, not every repair can be done with your own hands.

If the problems of refrigeration equipment are associated with violations in the electronic system or are caused by the refusal of intellectual control to perform their functions, it is better to contact the workshop to carry out repair

#one. Complex tasks for independent repair

Samsung refrigerators have several malfunctions that are difficult to eliminate without the experience of repair and the availability of special equipment.

If a refrigerant leak is detected, it is necessary not only to eliminate the defect of the tubes or their compounds, but also to compensate for the lost volume by refueling the system by freon. This is a difficult procedure that requires the stock of such a way and special equipment to measure its weight.

It is impossible to determine the volume of the refrigerant “by eye”, since in the best case the refrigerator refrigerator will not be observed by the cooling and snest mode, and in the worst there will be problems with the phase transition and a complete lack of cooling.

Electronic refueling scales for refrigerant are a mandatory tool for a specialist in repairing the compressors of the refrigerator. This is a specific and expensive equipment that most people do not have at home

If the compressor of the inverter refrigerator does not work, then you need to connect the working unit of the electronics and repeat the start attempt to start. In the case of a successful launch, it is possible to state the fact that the problem is on the side of the control board. If the start did not occur, the reason is in the compressor that needs to be changed.

Compressor replacement is the same procedure for any brands of refrigerators and freezers. It is needed to carry out a special tool (burner, accurate scales for refueling freon, gas station, etc.D.), the supply of refrigerant and the availability of experience in carrying out such work.

Therefore, it is better to call masters from the service center who will do all homework. Repair of electronics is possible in the presence of obvious signs of damage to the components of the board, such as capacitors (a sign of malfunction. bloating) or traces of contact oxidation.

(Recovery of electrical conductive circuits, as well as replacing the condenser or microcircuits requires special equipment (thermofen, tin.oxyx, a soldier with a wide sting, etc.D.) and some preparation.

If the cost of acquiring a new fee is high or the duration of its delivery is long, then you can contact the organization for the repair of computer equipment.

The electronics made by Samsung is of good quality and the simultaneous refusal of a large number of components is unlikely. Therefore, the terms and cost of the repair will most likely be insignificant.

When calling specialists to replace the compressor or restore the integrity of the evaporator with the slope of the refrigerant, it is necessary to free enough space, since the refrigerator will have to be deployed or pushed away from the wall

#2. Problems with the door and seal

The problem of air passing through doors can occur due to their incorrect position. This can be found using a plumb line. Before eliminating distortion, it is necessary to align the refrigerator using the level. The position of the doors is changed using adjusting bolts.

If the door is installed vertically, but there are signs of air pass, then the problem is in the seal. If the defect is in the presence of folds, then you can eliminate them by softening the rubber with heat using hot water or hair dryer.

Polyvinyl chloride seal is attached to glue, a flat screwdriver is needed to dismantle it. Using the shoulder blade and soft sponge, it is necessary to remove the remaining rubber and glue from the door of the door.

When installing a new seal, its corner parts can be slightly heated with a hairdryer to give them great elasticity. To fix in the door, you can use the glue “moment 88” or silicone sealant. For new models, a magnetic tape is integrated into the product, so there is no need to use adhesive substances for fixing to the door.

The magnetic tape securely attaches the seal to the metal door of the refrigerator. There is no need to use glue and wait until it dries. Elastic replacement operation can be quickly performed on a working device

#3. A malfunction of temperature sensors

Checking the performance of temperature sensors can be performed by measuring the resistance on the response of the connector of the main board of the electronic module.

Their location depends on the board, but there is an established color differentiation of wires:

If the resistance remains at the same level when temperature changes, this means that the sensor does not work. To change it, it is necessary to remove the rear panel that protects the evaporator and heating elements of the defrosting system.

The barrier is flooded. from 1500

The damper regulates the supply of cold air from the No Frost evaporator into the refrigerator chamber. Thus, the cooling of the products in the refrigerator compartment occurs. If the damper is stuck in a closed position, then cold air from the evaporator does not enter the refrigerator, and it does not cold. If the damper is stuck in an open position, then on the contrary, cold air constantly enters the department, and the refrigerator is rewinds.

Samsung Refrigerator Freezer Not Cooling Properly

Usually a damper motor comes out of the system. It goes in a case with a damper, so it is not sold separately. It is required to replace the damper completely.

Freon leaks occurred. from 2300

In the refrigerators Samsung No Frost, the leak arises:

The leak is accompanied by the constant operation of the refrigerator motor and high temperature in the freezer and refrigerated chambers.

If the leak occurred at the junction of the pipeline, then the master updates it by soldering or using the locking technology. With a leak in the circuit heating of the perimeter of the freezer, it is cut, the tubes are connected directly, and the refrigerator works without a heating circuit.

Details are not included in the price and are paid additionally. The final price is determined by the master after diagnosis.

Whatever the malfunction is in your two.chamber refrigerator Samsung No Frost, we will always come to the rescue. We arrive within a day after your call. We repair at home in the presence of a client. After the repair, we issue an official check with a guarantee of up to 2 years.

Outbound service “Ice Men”. we wish you health to your refrigerator.